

Module with an analog MQ7 carbon monoxide sensor. Carbon monoxide (most often called carbon monoxide) is a gas that is colorless, odorless, tasteless and extremely poisonous. Due to these properties, carbon monoxide is difficult to detect without a specialized device. With the help of the module with the MQ7 sensor, it is possible to build a detector that will detect CO in our environment. The module is powered with 5 V and has an analog output (Gravity connector) proportional to the measured concentration. The sensor is characterized by high sensitivity adjustable with a potentiometer and can measure the concentration of CO in the range from 20 to 2000 ppm. The Wiki page contains the manual and sample programs.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Set of 10 cables, 30 cm long, for analog sensors compatible with the Gravity standard. DFRobot FIT0031
Module with an analog MQ6 propane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0131
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
No product available!
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0465
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Module with an analog gas sensor. It allows you to measure the concentration of NO, NO2 and H2. DFRobot SEN0441
No product available!
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
No product available!
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
No product available!
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
No product available!
Module with LPG gas concentration sensor (MQ-6) in the range of 200 - 10,000 ppm. The module has an analogue output and a digital output triggered by exceeding the threshold of sensitivity. modMQ-6
A module for the detection of gases and vapors of alcohols, including ethanol.
The MQ-2 sensor allows the measurement of gas concentrations such as propane, butane, methane, LPG as well as alcohol and smoke. Sensor measuring range: up to 10,000 ppm
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132