Ethanol sensor module that uses electromechanical microsystem (MEMS) technology, resulting in a compact sensor, low power consumption, short acquisition time and fast response. It can measure concentrations from 1 to 500 ppm and is suitable for generating leak alarms in, for example, portable gas detectors. The sensor has an analog output and is supplied with a voltage of 3.3 V to 5 V. Full documentation and sample programs are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
No product available!
Development board with ESP32-S3-WROOM-1-N16R8 module. It is equipped with the OV2640 camera, making it ideal for applications such as image recognition. It offers a large memory capacity (8 MB PSRAM and 16 MB Flash memory) and a rich set of communication interfaces. DFRobot DFR0975
Development board with ESP32-S3-WROOM-1-N16R8 module. It is equipped with the OV2640 camera, making it ideal for applications such as image recognition. It offers a large memory capacity (8 MB PSRAM and 16 MB Flash memory) and a rich set of communication interfaces. DFRobot DFR0975
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
No product available!
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0127
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
No product available!
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Digital sensor dedicated to measuring carbon dioxide (CO2), air temperature and relative humidity. High performance, fast response and excellent stability make it an ideal solution for a variety of applications such as greenhouses, cities, poultry farms and transport stations. Seeed Studio 101991029
No product available!
The module with the sensor for the measurement of the concentration of carbon monoxide (MQ-7), allows the measurement of the concentration of carbon (CO) in the air. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
Module with nitrogen dioxide sensor made in MEMS technology. It allows gas detection in the range of 0.1 to 10 ppm and has an analog output. DFRobot SEN0574
A module for the detection of gases and vapors of alcohols, including ethanol.
Module with ethanol sensor made in MEMS technology. It allows gas detection in the range of 1 to 500 ppm and has an analog output. DFRobot SEN0569