- -zł10.12
Adapter for MQ gas sensor with potentiometer for analog signal calibration. The built-in configuration jumper V_SEL +3,3 V / + 5 V allows you to select the sensor supply voltage.
Attention!
The standard setting of the power jumper is +3.3 V. Before setting the jumper, check the power supply voltage of the sensor used.
Modulowo® DuoNect ™ solution
The Modulowo® DuoNect ™ solution enables fast and easy connection of expansion modules to Arduino , Raspberry Pi , Intel® Edison , STM32 Nucleo , Atmel Xplained , TI LaunchPad , Freescale Freedom and other platforms.
Data sheet
Manufacturer
Responsible person
The MQ-2 sensor allows the measurement of gas concentrations such as propane, butane, methane, LPG as well as alcohol and smoke. Sensor measuring range: up to 10,000 ppm
The MQ-7 sensor allows you to measure the concentration of carbon monoxide (carbon monoxide). The measuring range of the sensor is in the range of 10 - 10,000 ppm
The MQ-8 sensor allows the measurement of hydrogen concentration in the air. The measuring range of the sensor is in the range of 100 - 10,000 ppm.
The MQ-5 sensor allows the measurement of alcohol and gas concentrations, such as methane, LPG, and carbon monoxide. Sensor measuring range: up to 10,000 ppm
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
No product available!
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
Module with a gas concentration sensor MQ2, which enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020055
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
Module with BME680 sensor to measure the concentration of volatile organic compounds, pressure, temperature and humidity. It communicates via the I2C interface. Pimoroni PIM357
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Module with CO2, temperature and humidity sensor SCD-30. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4867
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72