Grove Temperature, Humidity, Pressure and Gas Sensor - module with BME680 sensor
ID: 583210
5906623416387
zł110.07
Tax included
zł89.49 tax excl.
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
Description
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The sensor has a wide measuring range and low energy consumption. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the I2C or SPI interface and is powered with the voltage of 3.3 V or 5 V. The BME680 has been specially developed for mobile applications and wearables, where size and low power consumption are key requirements. Full documentation of the module with examples of use is available on the product page.
Features
- Temperature measurement range: -40 to 85 ℃
- Temperature measurement accuracy: ± 1 ℃
- Temperature measurement resolution: 0.01 ℃
- Air humidity measuring range: 0 to 100%
- Air humidity measurement accuracy: ± 3%
- Humidity measurement resolution: 0.008%
- Atmospheric pressure measuring range: 300 to 1100 hPa
- Atmospheric pressure measurement accuracy: ± 0.6 hPa
- Pressure measurement resolution: 0.18 Pa
- Air quality measurement range: 0 to 500 (the higher the value, the worse the air condition)
- Interface: I2C, SPI
- I2C address: 0x76 (default), 0x77
- Supply voltage: 3.3 V or 5 V
- Dimensions: 40 x 20 x 7 mm
- Weight: 9.1 g
Kit contains
- Grove Temperature, Humidity, Pressure and Gas Sensor module
- Grove cable
583210
Data sheet
- Interface
- SPI/I2C
- Type of sensor
- BME680
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- VOC
- Sensor type
- Ciśnienia atmosferycznego
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł53.71
24h
Available quantity: 16
Available
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 227
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 17
Available
Grove module with temperature, humidity and pressure sensor. The board is equipped with a Grove connector and communicates via I2C or SPI. Seeed Studio 101020193
zł92.99
24h
Available quantity: 3
Available
Other products in the same category (16)
A small module - an infrared emitter (LED IR). The diode emits infrared light with a wavelength of 940 nm. With the help of the module, it is possible to transmit commands or signals that can be received by an infrared receiver. The transmission range is up to 10 meters. Seeed studio 101020026
zł18.45
24h
Available quantity: 3
Available
Module with digital light sensor TSL2561. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020030
zł30.71
24h
Available quantity: 2
Available
Module with 4-digit 7-segment display with red digits. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020044
zł33.37
24h
Available quantity: 2
Available
A small servo (23 x 11.5 x 24 mm) with a weight of 8.6 g, power supply 4.8-6V, maximum torque 1.8 kg / cm (at 6V). It has a connector compatible with the Grove standard. Seeed Studio 316010005
zł36.11
24h
Available quantity: 2
Available
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
zł563.83
24h
Available quantity: 1
Available
Speech recognition module with Nuvoton ISD9160 system, microphone, Flash memory and speaker output. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 101020232
zł104.60
24h
Available quantity: 2
Available
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
zł60.82
24h
Available quantity: 1
Available
Module with a reflection sensor (line sensor) RS-06WD. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020172
zł22.18
24h
Available quantity: 2
Available
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
zł79.32
24h
Available quantity: 4
Available
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
zł84.92
24h
Available quantity: 1
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
4 weeks
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 17
Available
3-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020006
zł15.72
24h
Available quantity: 5
Available
Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000
zł28.20
4 weeks
No product available!
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008
zł57.18
24h
Available quantity: 4
Available
Universal module for prototyping. It has 58 prototype fields and a Grove connector. Seeed Studio 101020035
zł11.32
24h
Available quantity: 3
Available
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513