

zł29.18 tax excl.
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. The module has a potentiometer, which can be used to adjust the power of the output gain. The module has a connector in accordance with the Grove standard.
The module can be used with the Base Shield V2 - shield extension with Grove connectors for Arduino
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492
No product available!
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
A module with a MEMS microphone that will allow you to detect a voice, a clap or a door slam. The board has an analog output. DFRobot SEN0487
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
MEMS microphone module that will allow voice detection, sound recording or audio transmission. It communicates via an I2S interface. DFRobot SEN0526
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-14262
No product available!
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
Audio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063