

In the case of working with a MCU:
Wiki : www.waveshare.com/wiki/Sound_Sensor
Weight: 0.007 kg
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
Sound card in the form of an expansion module with a USB adapter designed for NVIDIA Jetson Nano development kits. Waveshare Audio Card for Jetson Nano
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
No product available!
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
Module with omnidirectional digital microphone MEMS INMP441. It communicates via the I2S interface
No product available!
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492
No product available!
Sound Sensor