Audio module with THAT 1206 balanced line receiver and connector. Offers low distortion and high attenuation. Each terminal board combines the THAT 1206 integrated circuit, auxiliary elements and a 1/4 "TRS (Tip Ring Sleeve) socket. The board has an unbalanced output (OUT), positive and negative power lines (V +, V-) and ground (GND) Additionally, at each pin of the socket there are test points for signal (T, R, S) and normal (TN, RN, SN) contacts. Can be used in conjunction with a signal generator, power supply or oscilloscope. Full documentation with examples available. are on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
Audio module that allows you to play sounds from a USB memory, microSD card, via Bluetooth or FM radio. It is equipped with a microphone, 3.5 mm audio jack and control buttons
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
No product available!
MEMS microphone module that will allow voice detection, sound recording or audio transmission. It communicates via an I2S interface. DFRobot SEN0526
Module with omnidirectional digital microphone MEMS INMP441. It communicates via the I2S interface
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
Module with electret microphone and LM393 amplifier that will allow you to detect voice, clap, slam doors and other sounds using analog or digital output
Crowtail-Sound Sensor 2.0 is an analog sound sensor with a built-in amplifier, intended for measuring sound intensity levels. Ideal for interactive projects, sound-responsive systems and acoustic monitoring.
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-12642
No product available!
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
A module with a MEMS microphone that will allow you to detect a voice, a clap or a door slam. The board has an analog output. DFRobot SEN0487
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002