MEMS analog microphone module. It allows you to add sound acquisition to the application, enable voice detection, clap or slam doors. It can work with systems powered with a voltage of 3.3 V or 5 V. Full documentation with examples of use is available on the product wiki.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
All-in-one microcontroller especially designed for robotics application. Benefit from Arduino open source platform, it is supported by thousands of open source codes, and can be easily expanded with most Arduino Shields. The integrated 2 way DC motor driver and wireless socket gives a much easier way to start your robotic project. DFR0004
Bluno - BLE with Arduino Uno
Audio module that allows you to play sounds from a USB memory, microSD card, via Bluetooth or FM radio. It is equipped with a microphone, 3.5 mm audio jack and control buttons
Audio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
Module with omnidirectional digital microphone MEMS INMP441. It communicates via the I2S interface
No product available!
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
No product available!
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-12642
No product available!
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
A module with a MEMS microphone that will allow you to detect a voice, a clap or a door slam. The board has an analog output. DFRobot SEN0487