Module with MEMS microphone (SPH0645LM4H-B system). It has an I2S interface that has this type of peripheral systems for audio transmission. The interface has three lines: clock, data and left-right (Word Select) clock. After connecting to the microcontroller, the "I2S Master" system controls the clock signal and reads the data from the microphone. The I2S MEMS microphone has an input on the bottom of the system. The module can be powered by 1.6 ... 3.6 V. The module is compatible with M series Cortex circuits, such as Arduino Zero, Feather M0 or single board computers such as Raspberry Pi .
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492
No product available!
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-14262
No product available!
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
Audio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
Crowtail-Sound Sensor 2.0 is an analog sound sensor with a built-in amplifier, intended for measuring sound intensity levels. Ideal for interactive projects, sound-responsive systems and acoustic monitoring.
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
No product available!
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
Module with MEMS type microphone (SPH0645LM4H-B). It allows you to receive a sound signal and send it using the I2S audio interface. Powered by 1.6 ... 3.6V voltage. Adafruit 3421