

Module with WM8960 audio codec designed for Raspberry Pi minicomputers. It allows you to operate 1 W stereo speakers and two microphones via the I2S interface. It has been equipped with a 3.5 mm Jack connector for connecting headphones, two screw sockets for connecting speakers and a connector with an I2C interface. The user has two MEMS microphones and a button at his disposal. The module connects to the minicomputer via a 40-pin GPIO socket and has been designed for projects using a voice assistant. Full documentation with examples is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 1GB RAM LPDDR4, Broadcom VideoCore VI layout.
No product available!
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 2GB RAM LPDDR4, Broadcom VideoCore VI.
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 4 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 8 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
No product available!
MEMS microphone module that will allow voice detection, sound recording or audio transmission. It communicates via an I2S interface. DFRobot SEN0526
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
Module with MEMS type microphone (SPH0645LM4H-B). It allows you to receive a sound signal and send it using the I2S audio interface. Powered by 1.6 ... 3.6V voltage. Adafruit 3421
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-14262
No product available!
Module with electret microphone and LM393 amplifier that will allow you to detect voice, clap, slam doors and other sounds using analog or digital output
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
A module with a MEMS microphone that will allow you to detect a voice, a clap or a door slam. The board has an analog output. DFRobot SEN0487
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
The ICS43434 digital MEMS microphone module with an I2S interface that eliminates the need for A/D conversion and provides clean audio output in the range of 50 Hz to 15 kHz. With channel selection and low current consumption, it is suitable for stereo systems, voice recognition and portable applications. Compatible with popular microcontrollers, it provides high quality sound with low noise. Adafruit 6049
Module with WM8960 audio decoder that allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Adafruit 4757
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT