

MEMS INMP441 omni-directional microphone module with digital output and bottom port. The system consists of a MEMS sensor, an analog-to-digital converter, anti-aliasing filters, an energy management circuit and a standard 24-bit I2S interface. The INMP441 has a high SNR and a wide frequency response providing high-quality natural sound, making it an excellent choice for laptop, tablet or phone applications.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
No product available!
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
No product available!
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
The ICS43434 digital MEMS microphone module with an I2S interface that eliminates the need for A/D conversion and provides clean audio output in the range of 50 Hz to 15 kHz. With channel selection and low current consumption, it is suitable for stereo systems, voice recognition and portable applications. Compatible with popular microcontrollers, it provides high quality sound with low noise. Adafruit 6049
No product available!
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
No product available!
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
MEMS microphone module that will allow voice detection, sound recording or audio transmission. It communicates via an I2S interface. DFRobot SEN0526
No product available!
Module with electret microphone and LM393 amplifier that will allow you to detect voice, clap, slam doors and other sounds using analog or digital output
Module with omnidirectional digital microphone MEMS INMP441. It communicates via the I2S interface