zł183.50 tax excl.
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
Module with ozone detection sensor. It uses an electrochemical method to detect O3 in air, which ensures a stable and accurate measurement. The module is equipped with an I2C interface. It performs measurements up to 10 ppm with a resolution of 0.01 ppm. It is supplied with the voltage ranging from 3.3 V to 5.5 V. It can be used to build a portable detector, air quality monitoring devices or ozone disinfection devices.
Ozone is a gas that strongly stimulates the human body. It is produced mainly by the photochemical reaction of NOx and VOC emissions. Too much ozone in the air can cause coughing, shortness of breath and decreased lung function, as well as headaches, increased heart rate, memory loss and visual disturbances. The acceptable standard of ozone concentration that people can take in a day is 260 μg / m3.
When using the module, it should be remembered that it should not be immersed in an oxygen-free environment or flooded with resin. It should also not be used for a long time in an environment containing corrosive gas. The sensor should be protected against shock and vibration.
There is a user manual with sample programs on the product wiki page.
Attention!
The white waterproof and breathable membrane of the sensor on the module is strictly forbidden to open, otherwise it is regarded as artificial damage.Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
The MQ-7 sensor allows you to measure the concentration of carbon monoxide (carbon monoxide). The measuring range of the sensor is in the range of 10 - 10,000 ppm
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
The MQ-9 sensor allows the measurement of gas concentrations such as carbon monoxide, propane and methane. Sensor measuring range: 10 - 10,000 ppm
The MQ-6 sensor allows the measurement of LPG, propane and isobutane. The measuring range of the sensor is in the range of 300 - 10.000 ppm, while the output receives an analog signal.
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
Module with a knock-on sensor for measurement of methane, propane and carbon monoxide (MQ-9) concentrations. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
A sensor that detects the concentration of hydrogen. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0473
No product available!
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
No product available!
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
The MQ-2 sensor allows the measurement of gas concentrations such as propane, butane, methane, LPG as well as alcohol and smoke. Sensor measuring range: up to 10,000 ppm
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321