 
        
           
        
          Module with an analog MQ8 hydrogen sensor. Hydrogen is colorless, odorless and non-toxic, and because of these properties it is difficult to detect. By using the module with the MQ8 sensor, it is possible to build a portable detector that will detect the concentration of H2 in our environment. The module is powered with 5 V and has an analog output (Gravity connector) proportional to the measured concentration. The sensor is characterized by high sensitivity adjustable with a potentiometer and can measure the concentration of H2 in the range from 100 to 10,000 ppm. The Wiki page contains the manual and sample programs.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
 No product available!
Set of 10 cables, 30 cm long, for analog sensors compatible with the Gravity standard. DFRobot FIT0031
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0465
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with a BME688 sensor for measuring gas concentration, pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-19096
A module for the detection of gases and vapors of alcohols, including ethanol.
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
 No product available!
Sensor that detects the concentration of ozone. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0472
 No product available!
The module with a methane concentration sensor (MQ-4) in the range up to 10,000 ppm, has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with a smoke concentration sensor made in MEMS technology. It allows gas detection in the range of 10 to 1000 ppm and has an analog output. DFRobot SEN0570
The SCD-41 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22396
The MQ-2 sensor allows the measurement of gas concentrations such as propane, butane, methane, LPG as well as alcohol and smoke. Sensor measuring range: up to 10,000 ppm
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
 No product available!
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a Qwiic/STEMMA QT connector, it communicates via the I2C interface. Pimoroni PIM587
 No product available!
A sensor that detects the concentration of nitrogen dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0471
 No product available!
 
                    Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133