zł33.51 tax excl.
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Module with an analog MQ9 carbon monoxide and combustible gas sensor. Carbon monoxide (most often called carbon monoxide) is a gas that is colorless, odorless, tasteless and extremely poisonous. Due to these properties, carbon monoxide is difficult to detect without a specialized device. With the help of the module with the MQ9 sensor, it is possible to build a portable detector that will detect CO in our environment. Additionally, the MQ9 sensor can detect flammable gases such as methane and propane. The module is powered with 5 V and has an analog output (Gravity connector) proportional to the measured concentration. The sensor is characterized by high sensitivity regulated by a potentiometer and can measure the concentration of CO in the range from 20 to 2000 ppm and the concentration of combustible gases in the range of 100 to 10,000 ppm. The Wiki page contains the manual and sample programs.
Data sheet
Manufacturer
Responsible person
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
No product available!
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Set of 10 cables, 30 cm long, for analog sensors compatible with the Gravity standard. DFRobot FIT0031
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Module with a BME688 sensor for measuring gas concentration, pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-19096
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
No product available!
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536
The SCD-41 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22396
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
No product available!
Module with hydrogen sulphide sensor made in MEMS technology. It allows gas detection in the range of 0.5 to 50 ppm and has an analog output. DFRobot SEN0568
Module with ammonia sensor made in MEMS technology. It allows gas detection in the range of 1 to 300 ppm and has an analog output. DFRobot SEN0567
Module with a VOC sensor (volatile organic compounds) made in MEMS technology. It allows gas detection in the range of 5 to 500 ppm and has an analog output. DFRobot SEN0566
Methane sensor module made in MEMS technology. It allows gas detection in the range of 1 to 10000 ppm and has an analog output. DFRobot SEN0565
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134