- -zł51.13
zł72.37 tax excl.
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. The SGP30 air quality sensor provides information about the air quality in a room or house by monitoring volatile organic compounds around the sensor. SGP30 can return correct IAQ readings within 15 seconds of being turned on. The module is very resistant to pollution. You can read the output measurements of the total VOC gas sensor SGP30 (TVOC) in parts per billion (ppb), carbon dioxide equivalent (CO2) in parts per million (ppm) and H2. SGP30 communicates via I2C.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
IoT development board the size of Arduino, equipped with an ARM Cortex-M3 processor (STM32F205) and a Wi-Fi communication module (with an integrated antenna and uFL connector). SparkFun DEV-13321
This board combines the simplicity of the UNO’s Optiboot bootloader (which is used in the Pro series), the stability of the FTDI (which we all missed after the Duemilanove was discontinued) and the R3 shield compatibility of the latest Arduino UNO R3. SparkFun DEV-13975
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino UNO kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15444
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino Nano kit. It has a USB C. The board also has a USB-UART converter, a microphone, Lipo battery charging and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15443
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino Mega kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15442
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
Module with an infrared sensor MLX90640 - a measuring matrix with a resolution of 32x24 pixels. It offers an accuracy of 1.5°C and a viewing angle of 55x35°. Communication with the sensor takes place via the I2C interface. SparkFun SEN-14844
No product available!
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15733
Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476
GPS module with 72-channel GNSS SAM-M8Q receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART and I2C interfaces. SparkFun GPS-15210
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-18565
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19037
GPS module with SAM-M10Q GNSS receiver. The chip can receive data from all major positioning systems: GPS, GLONASS, Galileo, QZSS and BeiDou. It has derived UART and I2C interfaces. SparkFun GPS-21834
LiPo battery monitor module based on the MAX17048 chip. Allows the voltage and state of charge of the battery to be measured. SparkFun SPX-17715
Module with a differential pressure sensor SDP31 dedicated to measuring the flow rate and air velocity. The arrangement is characterized by wide measuring range from 260 to 1260 hPa and high measurement resolution (0.01 hPa). I2C or SPI communication. SparkFun SPX-14767
No product available!
SparkFun Qwiic kit. Contains 10 wires of different lengths and tips. It allows you to connect Qwiic modules to a programming platform or to a prototype board. SparkFun KIT-15081
Module with an ambient light sensor VEML6030 with a measuring range up to 120,000 lx. It enables light measurement with 16-bit resolution. I2C communication. SparkFun SEN-15436
Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334
A small module with a 3-axis magnetometer based on the Melexis MLX90393 system. Its resolution is 0.161 μT. I2C or SPI interface is used for communication. The I2C interface has been derived on connectors compatible with the Qwiic standard. SparkFun SEN-14571
Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531