Qwiic Speaker Amp - TPA2016D2 audio amplifier module
ID: 1181692
5906623419395
zł71.60
Tax included
zł58.21 tax excl.
Class D stereo sound amplifier based on the Texas Instruments TPA2016D2 circuit. It can work with 4 Ω speakers with power up to 2.8 W or 8 Ω with power up to 1.7 W in stereo mode. SparkFun DEV-20690
Description
Class D stereo sound amplifier based on the Texas Instruments TPA2016D2 circuit. It has volume control (gain), dynamic range compression (DRC), automatic gain control (AGC), on/off the amplifier and the possibility of its configuration via software via I2C. It can work with 4 Ω speakers with power up to 2.8 W or 8 Ω with power up to 1.7 W in stereo mode. The DRC and AGC functions allow you to "align" loud and quiet sections from the audio input and maximize the volume while protecting the speakers from damage by extremely loud playback. There are screw terminals on the board for audio input, power supply, power off and loudspeaker output. A 3.5mm TRS connector is included as an alternative to easily connect the audio cable, and the Qwiic system allows it to be easily connected to the rest of the system. The board is great for projects that require audio signal amplification for small speakers. Full documentation is available on the product page.
Features
- Class D stereo audio amplifier TPA2016D2
- Flexible operation with/without I2C
- Programmable Dynamic Range Compression (DRC) parameters
- Programmable parameters for Automatic Gain Control (AGC)
- Programmable volume control
- Selectable gain from -28dB to 30dB in 1dB steps (when compression is used)
- 4 compression ratios
- High PSRR: 80dB
- Fast startup time: 5 ms
- Short-circuit and thermal protection
- I2C address: 0x58
- Power supply: 2.5 V to 5.5 V via 2-pin screw terminal, 3.3 V via Qwiic connector
- Stereo output: 1.7W per channel into 8 Ω into 5V, 2.8W per channel into 4 Ω into 5V
- 3.5mm TRS jack for audio input
- Screw clamps
- Power inputs (PWR, GND)
- Audio inputs (GND, R, L) and SHDN
- Speaker output (R +, R-, L +, L-)
- 4-pin Qwiic connector
- Built-in I2C pull-up resistors (2.2kΩ)
1181692
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Available
Other products in the same category (16)
An audio module with a DAC converter and a stereo amplifier designed to work with the Raspberry Pi. Adafruit 3346
zł67.19
24h
Available quantity: 1
Available
Class D PAM8406 stereo digital audio amplifier module. The system allows you to connect two speakers with an impedance of 4 to 8 Ω and a power of 5 W per channel
zł4.72
4 weeks
No product available!
Audio module with DAC, stereo amplifier and display, designed to work with the Raspberry Pi. Pimoroni PIM484
zł159.64
24h
Available quantity: 4
Available
Stereo audio amplifier with Bluetooth 4.2 communication. It can be powered with the voltage from 19 to 24 V and has two outputs with a power of 80 W
zł773.17
24h
Available quantity: 1
Available
Class D mono digital audio amplifier module PAM8302. The system allows you to connect one loudspeaker with an impedance from 4 to 8 Ω and a power of 2.5 W
zł5.22
4 weeks
No product available!
Class-D stereo digital audio amplifier module PAM8403. The system allows you to connect two speakers with an impedance of 4 to 8 Ω and a power of 3 W. DFRobot DFR0119-O
zł24.77
4 weeks
No product available!
Available
Class D digital audio amplifier with Bluetooth 5.0 module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage ranging from 9 to 24 V
zł138.20
4 weeks
No product available!
PAM8610 digital stereo audio amplifier module. The system allows you to connect two speakers with an impedance from 4 to 8 Ω and a power of 10 W
zł17.26
4 weeks
No product available!
Zeenko ZK09-BM is a low-noise, ultra-wideband RF amplifier with an operating range up to 10 GHz, powered by a built-in battery. Thanks to its good linearity and noise performance, it is used in measurements, receiver paths and communication systems. Compact and mobile, it will work well both in laboratories and in the field.
zł103.97
6 weeks
No product available!
4-channel stereo audio mixer module. It has one output to which the summed signal from 4 inputs comes out. It is powered with the voltage from 5 to 12 V
zł72.56
24h
Available quantity: 2
Available
Class AB audio amplifier with three output channels. It can be powered with AC voltage from 8 to 18 V and has two outputs with a power of 18 W (left and right) and one with a power of 20 W (bass)
zł48.60
4 weeks
No product available!
No product available!
Audio preamplifier based on the NE5532 chip. Powered with symmetrical DC voltage in the range from 9 to 15 V
zł17.48
24h
Available quantity: 3
Available
Digital mono audio amplifier. It has one channel with a power of 30 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage from 8 to 26 V.
zł14.08
24h
Available quantity: 1
Available
4-channel stereo audio mixer in a metal housing. It has one output, on which the summed signal from 4 inputs is available. It is powered with the voltage from 5 to 12 V.
zł100.77
24h
Available quantity: 2
Available
Class D stereo sound amplifier based on the Texas Instruments TPA2016D2 circuit. It can work with 4 Ω speakers with power up to 2.8 W or 8 Ω with power up to 1.7 W in stereo mode. SparkFun DEV-20690