.png)
Tube HiFi stereo 3W + 3W (black)
ID: 588126
5906623448708
zł666.00
Tax included
zł541.46 tax excl.
HiFi stereo tube amplifier based on 6J1 and 6P1 tubes. Designed for use with loudspeakers up to 3 W and an impedance of 4 Ω or 8 Ω
Description
HiFi stereo tube amplifier based on 6J1 and 6P1 tubes. It allows you to adjust the volume using the built-in potentiometer and give a "sweet" sound color characteristic for devices with vacuum tubes. The amplifier allows you to connect two audio input channels through RCA connectors and outputs in the form of 3 W speakers and 4 Ω or 8 Ω impedance through banana connectors. It is powered by AC 230 V mains voltage via an IEC C14 socket (standard power socket used, for example, in computers).
The electronic module has been placed in a nice, aluminum housing, so it can be used not only as part of the audio system, but also as an element of decor. It is a good choice for both novice users and audiophiles.
Features
- Stereo amplifier
- Type: tube 6P1 (power amplifier), 6J1 (voltage amplifier)
- Frequency response: 30 Hz to 40 kHz (-1dB)
- Input sensitivity: 500 mV
- SNR: 80 dB
- Adjusting the volume level
- Input impedance: 10 kΩ
- Output power: 2 x 3 W with an impedance of 4 Ω or 8 Ω
- Input: RCA connectors
- Output: banana connectors
- Power switch
- Black colour
- Power supply: AC 100 to 250 V (IEC C14 socket)
- Dimensions: 124 x 132 x 166 mm
Kit contains
- HiFi tube amplifier
- 2 x 6P1
- 2 x 6J1 lamp
588126
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. SUCA-AUDIO TUBE-T1
zł253.08
24h
Available quantity: 2
Available
The Lanberg audio cable with a length of 500 cm enables stereo sound transmission via 3.5 mm minijack and 2x RCA (Chinch) connectors, ensuring compatibility with a wide range of devices such as computers, smartphones, TVs, and multimedia players. With high-quality craftsmanship, nickel-plated contacts, and a plastic braid, it guarantees excellent signal conductivity, minimal interference, and reliability. Its solid construction makes it suitable even for more demanding users. CA-MJRC-10CC-0050-BK
zł4.71
24h
Available quantity: 4
Available
Other products in the same category (16)
Sound terminal expansion board based on STA350BW for STM32 Nucleo
zł194.73
1 weeks
No product available!
Audio module with 8 Ohm loudspeaker and 8002B amplifier. It can be used as a buzzer and also play high-quality sound. The volume is controlled by a potentiometer. DFRobot FIT0449
zł31.78
24h
Available quantity: 73
Available
An audio module with a DAC converter and a stereo amplifier designed to work with the Raspberry Pi. Adafruit 3346
zł70.25
24h
Available quantity: 3
Available
Module with LM386 audio amplifier and loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 107020001
zł26.21
24h
Available quantity: 4
Available
Single-channel audio amplifier up to 100 W.
zł65.33
24h
Available quantity: 2
Available
A set with a vibration generator designed to transfer sounds through the human skeleton to the auditory center. DFRobot KIT0126
zł134.57
4 weeks
No product available!
Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475
zł95.58
24h
Available quantity: 2
Available
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
zł169.90
24h
Available quantity: 5
Available
Module containing TSH82 operational amplifier from STMicroelectronics. The system has two built-in amplifiers and each of them is available separately on the pins of the board as inverting amplifiers. Sparkfun BOB-14874
zł43.32
24h
Available quantity: 2
Available
LM386 audio amplifier module. It is supplied with the voltage ranging from 4 to 12 V. The set includes an 8 Ω, 0.5 W loudspeaker. DFRobot DFR0064
zł53.65
24h
Available quantity: 1
Available
The Class D digital audio amplifier module has two channels with a power of 15 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
zł30.34
24h
Available quantity: 4
Available
The Class D digital audio amplifier module has two channels with a power of 30 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
zł33.33
24h
Available quantity: 8
Available
Stereo audio amplifier with a power of 40 W (2 x 20 W) powered with the voltage of 12 V. Equipped with an audio input in the form of two chinch sockets and an audio jack 3.5 mm input
zł94.55
24h
Available quantity: 3
Available
LM386 audio amplifier module in a set with a loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 101020853
zł52.69
4 weeks
No product available!
Class D mono audio amplifier module with MAX98357 chip. It can work with a 4 to 8 Ω loudspeaker with a power of up to 3 W and communicates via the I2S interface. modMAX98357
zł12.20
4 weeks
No product available!
Class D PAM8403 stereo digital audio amplifier module. The system allows you to connect two speakers from 4 to 8 Ω with a power of 3 W per channel. modPAM8403
zł3.32
24h
Available quantity: 9
Available
HiFi stereo tube amplifier based on 6J1 and 6P1 tubes. Designed for use with loudspeakers up to 3 W and an impedance of 4 Ω or 8 Ω