zł32.78 tax excl.
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353
Module with an external counter TPL5110, which allows you to turn on the project after a set time and save energy if the device does not need to run all the time. It allows, for example, after reading measurements from sensors, sending data and storing them in the recorder, to turn off the power and then turn it on again, for example, after 1h.
The TPL5110's delay is configurable via resistors. Operation is facilitated by a six-way DIP switch, which allows you to select one of five pre-installed resistors. A sixth switch is attached to a pad that allows you to add your own PTH (or SMD) resistor. The delays associated with the pre-installed settings are labeled on the bottom of the board for quick configuration. In addition, more than one switch can be selected to connect resistors in parallel (up to 26 options, not including a custom resistor).
The Nano Power Timer supports voltages from 1.8 V to 5.5 V and currents up to 1.1 A. Timing configuration options range from 100 ms to two hours (preconfigured settings from 30s to 2h). There is a button on the board that will allow the user to quickly override the delay, so you can turn on your project at any time. Full documentation and usage examples are available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Li-Po battery with a nominal voltage of 3.7 V and a capacity of 220 mAh, equipped with a 150 mm cable terminated with a 2-pin JST connector with a 2.54 mm pitch. Integrated PCM protection safeguards against overcharge, over-discharge, and short circuit. Dimensions: 36 x 20 x 4 mm, weight: 6 g. Akyga LP402036
No product available!
Li-Po battery with a rated voltage of 3.7 V and a capacity of 400 mAh, equipped with a PCM protection and a 2.5 JST-RCY connector. Akyga LP403035
No product available!
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-17285
No product available!
The expansion module is designed to work with Raspberry Pi 400 - a portable computer built into the keyboard. The board has a 40-pin connector in the pin position and two Qwiic connectors. SparkFun DEV-17512
A set for building a mechanical keyboard based on the Qwiic Pro Micro module. It allows you to create your own keyboard with 14 buttons. SparkFun SPX-16184
A set for building a mechanical keyboard based on the Qwiic Pro Micro module. It allows you to create your own keyboard with 14 buttons with transparent caps. SparkFun SPX-17251
No product available!
Soil moisture sensor with I2C interface. The probe has two pointed tabs, making it easy to insert into the ground. The sensor is supplied with the voltage of 3.3 V or 5 V. SparkFun SEN-17731
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110\'s delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353
Ultrasonic distance sensor with a measuring range from 2 to 400 cm. It communicates via a standard interface (Echo, Trigger) or the I2C bus. SparkFun SEN-17777
Hub with Qwiic connectors that allows you to connect several boards to the evaluation kit. There is no built-in control system, but only splits one connector into 3 more. SparkFun BOB-18012
Kit for building a communication system based on QwiicBus. It contains two endpoint modules (EndPoint), an intermediary module (MidPoint) and two Ethernet cables. SparkFun KIT-17250
No product available!
Intermediate module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-18000
No product available!
End module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-16988
LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It communicates via the I2C or ANT interface. The set includes a module with Qwiic SparkFun SEN-18009 connectors
No product available!
Module with DA7280 vibration motor controller and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-17590
No product available!
Ultrasonic ToF (time-of-flight) rangefinder with a range of 4 cm to 1.2 meters. The sensor is able to simultaneously measure the range of several objects in its field of view. Communicates via I2C. SparkFun SPX-17271
No product available!
ToF laser rangefinder. It enables detection of many objects, has a field of view of about 25° and is able to detect objects at a distance of up to 3 m. Communicating via the I2C interface. SparkFun SPX-17072
No product available!
Module with a voltage level converter 3.3 V - 5 V intended for use in the Qwiic system. It has a built-in Step Up converter providing power supply with a voltage of 5 V and a current of up to 100 mA. SparkFun SPX-17238
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353