Module with an analog MQ4 methane sensor. Methane (CH4) is a gas that is colorless and odorless. The mixture of methane and air in a volume concentration of 4.5–15% is explosive. The formation of this mixture as a result of methane entering closed rooms (e.g. in hard coal mines) may cause an explosion. Due to its properties, methane is difficult to detect without a specialized device. Using the module with the MQ4 sensor, it is possible to build a detector that will detect CH4 in our environment. The module is powered with 5 V and has an analog output (Gravity connector) proportional to the measured concentration. The sensor is characterized by high sensitivity adjustable with a potentiometer and can measure the concentration of methane in the range from 200 to 10,000 ppm. The Wiki page contains the manual and sample programs.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466
Module with the MQ3 analog alcohol sensor. It enables gas detection and construction of a simple breathalyzer. The module is powered by 5 V and has an analog output. DFRobot SEN0128
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0127
Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133
Module with an analog MQ5 LPG sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0130
Module with an analog MQ6 propane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0131
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
No product available!
Module with gas sensor SGP30. It allows you to measure the content of total volatile organic compounds (TVOC), carbon dioxide equivalent (eCO2), ethanol and H2 in the air. M5Stack U088
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129