New products
New products New products
zł9,349.00
4 weeks
zł173.58
Delivery date unknown
Grove Multichannel Gas Sensor v2
ID: 583081
5906623415243
zł158.82
Tax included
zł129.12 tax excl.
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Description
Module with gas sensors GM-102B, GM-302B, GM-502B and GM-702B, which allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). It is based on the STM32F030 microcontroller, which supports reading data from sensors and transmits them via the I2C interface. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module is supplied with the voltage from 3.3 V to 5 V. Full documentation of the module with examples of use is available on the product page.
Features
- GM-102B
- Gas type: NO2
- Response time: ≤ 30 seconds
- Recovery time: ≤ 60 s
- Resistance: 80 ± 20 Ω
- GM-302B
- Gas type: ethanol
- Measurement range: 1 to 500 ppm
- Resistance: 60 to 100 Ω
- Power consumption PH ≤50mW
- Body resistance: 1 kΩ to 30 kΩ (in ethanol 50 ppm)
- Sensitivity: Rs (in air) / Rs (in ethanol 50ppm) ≥ 3.0
- Concentration characteristic slope (α): ≤0.9 (R200ppm / R50ppm Ethanol)
- GM502B
- Gas type: VOC (VOC), ethanol
- Measurement range: 1 to 500 ppm
- Resistance: 80 ± 20 Ω
- Power consumption PH ≤50mW
- Body resistance: 1 kΩ to 30 kΩ (in ethanol 50 ppm)
- Sensitivity: R0 (in air) / Rs (in ethanol 50ppm) ≥ 3.0
- Concentration characteristic slope (α): ≤0.9 (R200ppm / R50ppm Ethanol)
- GM702B
- Gas type: CO
- Measurement range: 5 to 5000 ppm
- Resistance: 80 ± 20 Ω
- Power consumption PH ≤50mW
- Body resistance: 1 kΩ to 30 kΩ (in CO 150 ppm)
- Sensitivity: R0 (in air) / Rs (in CO 150 ppm) ≥ 3.0
- Concentration characteristic slope (α): ≤0.9 (R200ppm / R150ppm CO)
- I2C interface
- I2C address: 0x55
- Supply voltage: 3.3 V to 5 V
Kit contains
- Grove Multichannel Gas Sensor v2
- Grove cable
583081
Data sheet
- Interface
- I2C
- Type of sensor
- inny
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- VOC
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 240
Available
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
zł189.00
Delivery date unknown
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 17
Available
The expansion module is designed for Arduino Mega and Google ADK boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020027
zł27.36
24h
Available quantity: 4
Available
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
zł19.54
24h
Available quantity: 2
Available
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
zł55.95
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ2, which enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020055
zł41.71
24h
Available quantity: 2
Available
Other products in the same category (16)
GrovePi + is an extension in the form of a HAT overlay intended for Raspberry Pi computers (B / B + / A + / 2/3/3 +). The module has 15 connectors to which modules / sensors compatible with the Grove standard can be connected. Seeed Studio 103010002
zł298.47
24h
Available quantity: 3
Available
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
zł37.82
24h
Available quantity: 1
Available
The module is compatible with the Grove Base Shield and designed to implement a wireless serial connection. It uses BluetoothV2.0+EDR and UART communication. Seeed Studio 113020008
zł110.24
24h
Available quantity: 3
Available
5-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020272
zł8.23
24h
Available quantity: 2
Available
Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000
zł28.20
4 weeks
No product available!
Red mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070020
zł10.39
24h
Available quantity: 1
Available
Green mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070027
zł11.54
24h
Available quantity: 2
Available
intelligent gesture recognition module equipped with an IR camera module PAG7646J1, PAG7661QN (ISP) and a LED for backlighting. Recognizes and interprets hand gestures by recognizing the image recorded by an infrared camera. Seeed Studio 101991067
zł110.09
24h
Available quantity: 2
Available
Module with 2-element 14-segment display with red backlight. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 104020132
zł37.20
24h
Available quantity: 3
Available
Module with SHT31 temperature and humidity sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020212
zł52.95
24h
Available quantity: 1
Available
Module with a SI1151 light sensor that can detect waves with a wide range of wavelengths: visible and infrared light. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020089
zł54.75
24h
Available quantity: 3
Available
Angled Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990037
zł8.17
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ2, which enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020055
zł41.71
24h
Available quantity: 2
Available
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090
zł64.50
4 weeks
No product available!
The expansion module is designed for Arduino Nano boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103100124
zł14.23
24h
Available quantity: 2
Available
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
zł43.95
24h
Available quantity: 1
Available
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820