

SCD41 CO2, temperature and humidity sensor module. It allows ambient carbon dioxide concentrations to be measured in the range from 400 to 5,000 ppm. In addition, it has an integrated temperature and humidity sensor, making it suitable for environmental sensing, scientific experiments and air quality studies. It can be used in systems with an operating voltage of 3.3 V or 5 V, and communication is via an I2C interface (Gravity connector). Full documentation and examples are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Methane sensor module made in MEMS technology. It allows gas detection in the range of 1 to 10000 ppm and has an analog output. DFRobot SEN0565
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466
No product available!
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5190
Pololu MQ Gas Sensor Carrier
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536