Gravity: H2 Sensor - module with a hydrogen concentration sensor
ID: 1178462
5902186310056
zł896.82
Tax included
zł729.12 tax excl.
A sensor that detects the concentration of hydrogen. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0473
Description
A sensor that detects the concentration of hydrogen. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of hydrogen in industry and environmental protection. Full documentation and examples of use are available on the product page.
Features
- Detected gas: Hydrogen (H2)
- Measuring range: 0 to 1000 ppm
- Output signal: I2C, UART (0 to 3V), analog output
- Working temperature: -20 to 50 ℃
- Working humidity: 15 to 90% RH
- Service life:> 2 years (in air)
- Operating voltage: 3.3 to 5.5 V DC
- Working current: ＜ 5mA
- Adapter plate dimensions: 37 x 32 mm
Kit contains
- Gravity: H2 Signal Conversion Board
- H2 probe
- 4-pin Gravity cable
1178462
Data sheet
- Interface
- I2C/UART/Syganał analogowy
- Type of sensor
- inny
- Power supply voltage
- 3,2 - 5,5 V
- Concentration measurement
- H2
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
24h
Available quantity: 57
Available
Available
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
zł348.46
24h
Available quantity: 2
Available
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł28.22
24h
Available quantity: 6
Available
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
zł41.22
24h
Available quantity: 1
Available
Other products in the same category (16)
The module with an alcohol sensor (MQ-3), allows you to measure the concentration of ethanol in the air. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
zł7.20
24h
Available quantity: 14
Available
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
zł722.94
4 weeks
No product available!
Integrated gas sensor, pressure, humidity and temperature in the LGA-8 housing. Bosch Sensortec BME680
Regular pricezł104.67zł79.90
24h
Available quantity: 28
Available
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
zł158.82
24h
Available quantity: 2
Available
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
zł95.23
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ2, which enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020055
zł34.92
24h
Available quantity: 1
Available
Methane sensor module made in MEMS technology. It allows gas detection in the range of 1 to 10000 ppm and has an analog output. DFRobot SEN0565
zł23.54
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł55.71
24h
Available quantity: 3
Available
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
zł55.95
24h
Available quantity: 2
Available
A sensor that detects the concentration of sulfur dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0470
zł702.96
4 weeks
No product available!
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
zł119.84
24h
Available quantity: 3
Available
Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514
zł97.10
24h
Available quantity: 2
Available
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
zł225.71
4 weeks
No product available!
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
zł14.62
24h
Available quantity: 15
Available
Pololu MQ Gas Sensor Carrier
zł5.97
24h
Available quantity: 8
Available
SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536
zł265.36
24h
Available quantity: 1
Available
A sensor that detects the concentration of hydrogen. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0473