zł587.76 tax excl.
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
A sensor that detects the concentration of ammonia. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of ammonia in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
Volatile gas sensor module, including LPG, natural gas, natural gas
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
No product available!
The MQ-5 sensor allows the measurement of alcohol and gas concentrations, such as methane, LPG, and carbon monoxide. Sensor measuring range: up to 10,000 ppm
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
No product available!
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Module with nitrogen dioxide sensor made in MEMS technology. It allows gas detection in the range of 0.1 to 10 ppm and has an analog output. DFRobot SEN0574
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469