Air quality sensor module based on the ENS160 system. It has been specially designed for indoor air quality monitoring and offers the detection of multiple IAQ parameters (TVOC, eCO2, AQI). The innovative TrueVOC ™ technology provides the sensor with the highest accuracy, fast response and protection against interference. The module is powered with the voltage of 3.3 V and communicates via the I2C or SPI interface. Full documentation is available on the product Wiki page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
Air quality sensor based on the ENS160 chip and enclosed in a housing. It communicates via an I2C interface. DFRobot SEN0515
Indoor air quality measurement module, combining two high-end Sensirion sensors – SCD41 and SEN55. It offers a comprehensive set of measurements, including CO2 concentration, volatile organic compounds (VOC), suspended dust (PM1.0, PM2.5, PM4, PM10), as well as temperature and relative humidity. SparkFun SEN-25200
No product available!
Laser dust sensor is a digital universal particle concentration sensor,it can be used to obtain the number of suspended particulate matter in a unit volume of air within 0.3 to 10 microns, namely the concentration of particulate matter, and output with digital interface, also can output quality data of per particle. DFRobot SEN0177
PM2.5 dust sensor powered by 5V, communication via the UART interface. Sharp GP2Y1051AU0F
PMS7003 is a kind of digital and universal particle concentration sensor, which can be used to obtain the number of suspended particles in the air, i.e. the concentration of particles, and output them in the form of digital interface
No product available!
The PMSA003 air quality sensor module is designed for the Raspberry Pi. It allows you to analyze the amount of pollutants based on the concentration of PM1.0, PM2.5 and PM10 particles. SB Components 20768
Module with PM2.5 HM3301 dust sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020613
Air quality sensor module PMSA003I. It allows for a precise analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. Adafruit 4632
Sensirion\'s SEN54 sensor module, which combines a sensor that allows measurement of particulate matter, VOCs, humidity and temperature in a single housing. SparkFun SEN-19325
No product available!
Digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels, intended for indoor air quality monitoring in personal devices such as watches and phones, but we’ve put it on a breakout board so you can use it as a regular I2C device. SEN-14193
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
No product available!
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
Sharp GP2Y1010AU0F dust and particle concentration sensors. It is supplied with the voltage from 5 to 7V. Has an analog output. DFRobot SEN0144
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515