A sensor that detects the concentration of ozone. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of ozone in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer
Responsible person
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
No product available!
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536
No product available!
The SCD-41 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22396
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
Module with hydrogen sulphide sensor made in MEMS technology. It allows gas detection in the range of 0.5 to 50 ppm and has an analog output. DFRobot SEN0568
Module with ammonia sensor made in MEMS technology. It allows gas detection in the range of 1 to 300 ppm and has an analog output. DFRobot SEN0567
No product available!
Module with a VOC sensor (volatile organic compounds) made in MEMS technology. It allows gas detection in the range of 5 to 500 ppm and has an analog output. DFRobot SEN0566
Methane sensor module made in MEMS technology. It allows gas detection in the range of 1 to 10000 ppm and has an analog output. DFRobot SEN0565
Module with a smoke concentration sensor made in MEMS technology. It allows gas detection in the range of 10 to 1000 ppm and has an analog output. DFRobot SEN0570
Module with a formaldehyde sensor made in MEMS technology. It allows gas detection in the range of 0 to 3 ppm and has an analog output. DFRobot SEN0563
Module with ethanol sensor made in MEMS technology. It allows gas detection in the range of 1 to 500 ppm and has an analog output. DFRobot SEN0569
Module with nitrogen dioxide sensor made in MEMS technology. It allows gas detection in the range of 0.1 to 10 ppm and has an analog output. DFRobot SEN0574
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
No product available!
Digital sensor dedicated to measuring carbon dioxide (CO2), air temperature and relative humidity. High performance, fast response and excellent stability make it an ideal solution for a variety of applications such as greenhouses, cities, poultry farms and transport stations. Seeed Studio 101991029
No product available!
Sensor that detects the concentration of ozone. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0472