

A sensor that detects the concentration of oxygen. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of oxygen in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133
A sensor that detects the concentration of nitrogen dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0471
No product available!
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466
No product available!
The MQ-9 sensor allows the measurement of gas concentrations such as carbon monoxide, propane and methane. Sensor measuring range: 10 - 10,000 ppm
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
No product available!
Module with BME680 sensor to measure the concentration of volatile organic compounds, pressure, temperature and humidity. It communicates via the I2C interface. Pimoroni PIM357
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the UART interface or the analog output. Seeed Studio 101020912
No product available!
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5190
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
No product available!
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
The MQ-5 sensor allows the measurement of alcohol and gas concentrations, such as methane, LPG, and carbon monoxide. Sensor measuring range: up to 10,000 ppm
Module with CO2, temperature and humidity sensor SCD-40. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5187
Air quality sensor module based on the SGP40 system. It uses CMOSens® technology by Sensirion and provides information on air quality. Waveshare SGP40 VOC Sensor
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0465