zł961.30 tax excl.
A sensor that detects the concentration of phosphine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0476
A sensor that detects the concentration of phosphine. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of phosphine in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
Air quality sensor module based on the SGP40 system. It uses CMOSens® technology by Sensirion and provides information on air quality. Waveshare SGP40 VOC Sensor
No product available!
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
A sensor that detects the concentration of nitrogen dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0471
No product available!
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
The MQ-7 sensor allows you to measure the concentration of carbon monoxide (carbon monoxide). The measuring range of the sensor is in the range of 10 - 10,000 ppm
Module with a formaldehyde sensor made in MEMS technology. It allows gas detection in the range of 0 to 3 ppm and has an analog output. DFRobot SEN0563
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
The MQ-8 module allows the measurement of hydrogen concentration in the air. It has an analogue output and an output triggered by exceeding the threshold of sensitivity.
No product available!
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
A sensor that detects the concentration of phosphine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0476