 
        
           
        
           
         
           
           
          A sensor that detects the oxygen concentration. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the gas concentration in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the UART interface or the analog output and has an integrated temperature compensation algorithm. It can be widely used for oxygen detection in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
4-core cable, 20 cm long, terminated on both sides with a Grove plug. Compatible with the interface used in Seeed Studio and M5Stack modules. Seeed Studio 110990027
4-core cable, 50 cm long, terminated on both sides with a Grove plug. Compatible with the interface used in the M5Stack modules. M5Stack A034-C
Expansion module for Seeeduino XIAO. It is equipped with Grove connectors and a lithium battery charging system. Seeed Studio 103020312
 No product available!
The expansion module is designed for Arduino Nano boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103100124
A 4-core cable with a length of 50 cm, both terminated with a Grove plug. Seeed Studio 110990038
A 4-core cable with a length of 30 cm, both terminated with a Grove plug. Seeed Studio 110990040
4-core cable with a length of 15 cm, terminated on one end with a Grove plug, and on the other with a male goldpin connector. Seeed Studio 110990210
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
 No product available!
Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514
A sensor that detects the concentration of nitrogen dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0471
 No product available!
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
Module with the MiCS-5524 analog gas sensor. It allows you to measure the concentration of CO, CH4, 2H5OH, C3H8, C4H10, H2, H2S and NH3. DFRobot SEN0440
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
Module with a VOC sensor (volatile organic compounds) made in MEMS technology. It allows gas detection in the range of 5 to 500 ppm and has an analog output. DFRobot SEN0566
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
 No product available!
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
Module with gas sensor SGP30. It allows you to measure the content of total volatile organic compounds (TVOC), carbon dioxide equivalent (eCO2), ethanol and H2 in the air. M5Stack U088
 
                    A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the UART interface or the analog output. Seeed Studio 101020912