Gravity: Electrochemical Oxygen Sensor - module with an oxygen concentration sensor
ID: 1179237
5902186310377
zł498.61
Tax included
zł405.37 tax excl.
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
Description
Module with an oxygen concentration sensor in the environment. It allows you to measure the oxygen volume in the full range from 0 to 100%. It is characterized by high accuracy and stability of measurements. It has a built-in calibration algorithm, and the sensor probe, based on the principle of electrochemistry, has strong anti-interference properties and a long service life. The module communicates via the I2C interface. Can be widely used in areas such as portable and air quality monitoring devices.
The sensor can be calibrated by the user for more accurate measurements. Calibration manual and sample programs are available on the product page.
Features
- Oxygen detection
- Interface: Gravity I2C
- Measuring range: 0 to 100% by volume
- Response time: ≤5 seconds
- Pressure range: 0.5 to 2 bar
- Service life:> 2 years
- Voltage: 3.3 to 5.5 V
- Working temperature: -20 to 50 ℃
- Operating humidity: 0 to 99% RH (non-condensing)
- Dimensions: 32 x 27 mm
Kit contains
- Gravity module: Electrochemical Oxygen Sensor
- AO2 probe
- Gravity-4pin I2C cable
- Molex 2510 PH2.0 cable 20 cm
1179237
Data sheet
- Interface
- I2C
- Type of sensor
- AO2
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- O2
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.65
24h
Available quantity: 1
Available
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
zł371.12
24h
Available quantity: 1
Available
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł28.09
24h
Available quantity: 4
Available
Other products in the same category (16)
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
zł106.84
24h
Available quantity: 1
Available
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
zł102.36
24h
Available quantity: 3
Available
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
zł722.94
4 weeks
No product available!
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
zł79.85
24h
Available quantity: 3
Available
The module with a smoke sensor and flammable gases (MQ-2) allows the measurement of gas concentrations such as natural gas, hydrogen as well as smoke and ethanol. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity. modMQ-2
zł5.20
24h
Available quantity: 3
Available
Module with ozone detection sensor. It performs measurements up to 10 ppm with a resolution of 0.01 ppm. It has a UART output and an analog output. ZE25-O3
zł249.53
24h
Available quantity: 2
Available
Module with a knock-on sensor for measurement of methane, propane and carbon monoxide (MQ-9) concentrations. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
zł10.00
24h
Available quantity: 4
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł55.71
Delivery date unknown
No product available!
Module with an analog MQ5 LPG sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0130
zł32.83
4 weeks
No product available!
Module with the MQ3 analog alcohol sensor. It enables gas detection and construction of a simple breathalyzer. The module is powered by 5 V and has an analog output. DFRobot SEN0128
zł33.27
24h
Available quantity: 1
Available
Module with an analog MQ6 propane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0131
zł32.83
24h
Available quantity: 1
Available
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
zł722.94
4 weeks
No product available!
Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972
zł356.05
4 weeks
No product available!
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
zł102.93
24h
Available quantity: 1
Available
A sensor that detects the concentration of hydrogen chloride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0474
zł925.55
4 weeks
No product available!
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
zł339.00
3 weeks
No product available!
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496