 
        
           
        
           
         
           
           
           
          Gravity: I2C 12-Bit DAC Module is a module with a 12-bit DAC (digital-to-analog) converter. The transducer allows you to generate analog signals such as sinusoidal or triangular. It has a built-in EEPROM memory, thanks to which the output signal is sustained in the event of a power loss and the operation resumes when the power supply is recovered. The I2C interface is used for communication with the module and the module has an I2C device address switch (two addresses available). Thanks to the Gravity connector, the module can be easily connected to Arduino or Raspberry Pi . The product can be used, for example, when generating audible signals.
Attention!
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Module with 12-bit DAC converter and built-in EEPROM memory. The module is supplied with the voltage from 2.7 to 5.5V, the I2C interface is used for communication. SparkFun BOB-12918
Dual-channel DAC converter compatible with the SYZYGY standard. The module can simultaneously generate two 5V signals with 14-bit resolution and sampling frequency up to 100MS/s. The module is compatible with Eclypse Z7 and Genesys ZU evaluation kits. Digilent Zmod AWG 1411 410-397
 No product available!
A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712
Gravity module designed based on the GP8501 system. It is a two-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.5% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1037
Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034
Gravity module designed based on the GP8211 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1071
Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036
Dual-channel ADC converter compatible with the SYZYGY standard. The module can simultaneously obtain two 25V signals with 14-bit resolution and sampling frequency up to 100MS/s. The module is compatible with Eclypse Z7 and Genesys ZU evaluation kits. Digilent Zmod Scope 1410-105 (410-396)
 No product available!
Extension module with ADC AD9250 converter dedicated to FPGA boards. It offers 4 input channels with a resolution of 14 bits and an ANSI/VITA 57.1 FMC connector. Numato Lab NLFMCADC001
 No product available!
A 16-bit DAC converter module designed to work with M5Stack sets. It enables the conversion of analog signals into a digital signal. M5Stack ADC Unit
A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037
 No product available!
Module with 4-channel ADC ADS1115 converter. The system enables analog voltage conversion for single signals and differential signals with 16-bit resolution. I2C communication
ADC converter module with 7 measurement channels (measuring 0-5V, 0-10V voltage and 4-20 mA current). Communicates via RS485 industrial interface using Modbus RTU protocol. R4AVA07
 No product available!
A 2-channel DAC converter module with an output voltage range from 0 to 10 V. It is powered by 3.3 V to 5 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0971
Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836
Extension module with ADC AD7616 converter dedicated to FPGA boards. It offers 32 channels with a resolution of 16 bits and an FMC LPC connector. Numato Lab NLFMCADC002
 No product available!
 
                    Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552