

Module with a 16-channel PWM PCA9685 driver. The system allows you to control servos or LEDs with 12-bit PWM resolution. The servos are connected to the module through the 3-pin connectors, and the 5 V power supply through the clamp connector. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V or 5 V. Full documentation with examples of use is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
Module with TB6612FNG DC motors dual driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020103
The expansion module is designed for Arduino Mega and Google ADK boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020027
A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712
A module with an NFC PN532 transceiver, which supports proximity communication at the frequency of 13.56 MHz. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 113020006
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
No product available!
The module with the tilt sensor, the sensor output is a digital signal. The module has a connector in accordance with the Grove standard. Seeed studio 101020025
Module with temperature and humidity sensor DHT11. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020011
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
ToF VL53L0X distance sensor module with a range of 3 to 200 cm. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020532
Module with PIR S16-L221D motion sensor. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020617
No product available!
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
Waterproof strip with RGB LED diodes, 1 m long (60 LEDs per meter). The LEDs are mounted on a flexible white PCB, the tape has a Grove connector. Seeed Studio 104020109
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
IoT module with the STM32WLE5JC chip, which connects the microcontroller with the ARM Cortex-M4 core and the LoRa SX126X module. There is a Grove connector on the board. Seeed Studio 113020091
Module with a button and yellow LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020045
No product available!
The module with an electromagnet is powered by a DC voltage of 3.3/5V V with a holding force of 1 kg. It can be used to build a DIY electromagnetic lock, smart cabinet or door. Seeed Studio 101020073
Module with a touch keyboard (12 buttons) based on the ATtiny1616 microcontroller. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 101020636
Module with a 16-channel PWM PCA9685 driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020102