Grove UART WiFi V2 - WiFi module with ESP8285
search
  • Grove UART WiFi V2 - WiFi module with ESP8285
  • Grove UART WiFi V2 - WiFi module with ESP8285
  • Grove UART WiFi V2 - WiFi module with ESP8285
ID: 583219
5906623415861
zł71.75
Tax included

zł58.33 tax excl.

Transceiver module equipped with SoC ESP8285 IoT enabling communication with WiFi networks. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 113020011

24h
Available
Available quantity: 1
Kamami is the official distributor of Seeed Studio modules and development kits. All products of this brand in our offer are original and come directly from the manufacturer.

Description

Transceiver module equipped with SoC ESP8285 IoT. Thanks to the integrated TCP/IP protocol stack, it enables the microcontroller to communicate with WiFi networks. Each ESP8266 module is pre-programmed with the firmware of the AT command set, which means you can send simple text commands to control the device. The SoC features integrated WEP, WPA/WPA2, TKIP, AES and WAPI, can act as an access point with DHCP, connect to existing WiFi networks, and has configurable MAC and IP addresses. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the UART interface and is supplied with the voltage of 3.3 V or 5 V. Full documentation of the module with examples of use is available on the product page.

Features

  • ESP8285 chip
  • WiFi 802.11 b/g/n (2.4 GHz) communication
  • WiFi Direct (P2P) software access point
  • It supports three modes: AP, STA and AP + STA coexistence mode
  • Integrated TCP/IP protocol stack
  • LwIP
  • Integrated TR switch, balun, LNA, power amplifier
  • Integrated PLL, regulators, DCXO and energy management units
  • +19.5 dBm output power in 802.11b mode
  • Hardware accelerators for CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC
  • WPA / WPA2 PSK and WPS driver
  • A-MPDU and A-MSDU aggregation and 0.4 ms guard interval
  • UART interface, 115200
  • QoS management
  • Wake-up function
  • PCB antenna
  • Reset button
  • 1 MB of built-in SPI flash memory
  • Supply voltage: 3.3 V or 5 V
  • Current consumption in Low Power mode: up to 10 uA
  • Dimensions: 40 x 20 x 7 mm
  • Weight: 8 g

Kit contains

  • Grove UART WiFi V2
  • Grove cable
583219

Data sheet

Wi-Fi standard
802.11 b/g/n
Logic voltage
3,3 V/5 V
Wi-Fi chip
ESP8285
Frequency range
2,4 GHz
Baud rate
115200 bps
Antenna connector
Brak
Power supply voltage
3,3 V/5 V

Manufacturer

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Responsible person

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

You might also like

Other products in the same category (16)