zł42.14 tax excl.
Waterproof strip with RGB LED diodes, 1 m long (60 LEDs per meter). The LEDs are mounted on a flexible white PCB, the tape has a Grove connector. Seeed Studio 104020109
Strip with RGB LED diodes, 1 m long, white. The tape is waterproof and there are 60 LEDs for each meter. The product uses WS2813 diodes (newer version of WS2812 diodes), which support the recovery system after a line interruption - in the event of a single diode failure, the LED strip will continue to glow. This system works until there are two damaged LEDs in succession. The tape is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. It is powered with the voltage of 5 V and consumes up to 3.6 A per meter.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
Waterproof strip with RGB LED diodes, 1 m long (30 LEDs per meter). The LEDs are mounted on a flexible white PCB, the tape has a Grove connector. Seeed Studio 104020108
Module with digital light sensor TSL2561. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020030
Module with 4-digit 7-segment display with red digits. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020044
A small servo (23 x 11.5 x 24 mm) with a weight of 8.6 g, power supply 4.8-6V, maximum torque 1.8 kg / cm (at 6V). It has a connector compatible with the Grove standard. Seeed Studio 316010005
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
Speech recognition module with Nuvoton ISD9160 system, microphone, Flash memory and speaker output. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 101020232
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
Module with a reflection sensor (line sensor) RS-06WD. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020172
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
3-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020006
Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008
Universal module for prototyping. It has 58 prototype fields and a Grove connector. Seeed Studio 101020035
Grove adapter for 3.5mm screw connector. Seeed Studio 103020007
Waterproof strip with RGB LED diodes, 1 m long (60 LEDs per meter). The LEDs are mounted on a flexible white PCB, the tape has a Grove connector. Seeed Studio 104020109