Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)
The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8–28 V, with derated performance down to 5 V and transient protection to 40 V. The board ships with connectors installed as shown (no soldering required).
![]() |
The jrk 21v3 is a versatile, general-purpose motor controller that supports a variety of interfaces, including USB. The broad operating range from 5 V to 28 V and continuous output current of 3 A (5 A peak) allow this board to control most small DC brushed motors. Analog voltage and tachometer (frequency) feedback options allow quick implementation of closed-loop servo systems, and a free configuration utility (for Windows 7, Vista, or Windows XP) allows easy calibration and configuration through the USB port.
Key improvements over competing products and earlier Pololu motor controllers with feedback include:
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
![]() |
![]() |
| Motor channels: | 1 |
|---|---|
| Operating voltage: | 5 – 28 V |
| Continuous output current: | 3 A |
| Peak output current: | 5 A |
| Auto-detect baud rate range: | 300 – 115,200 bps |
| Available fixed baud rates: | 300 – 115,200 bps |
| Available PWM frequencies: | 20 kHz, 5 kHz |
| Reverse voltage protection?: | Yes |
| USB connector style: | USB Mini-B |
The jrk 21v3 is the smaller of two jrk motor controllers. For a higher-power version, see the jrk 12v12.
|
|
The jrk 21v3 is available in two versions: “fully assembled” with terminal blocks and 0.1" male header pins pre-installed (left picture above), and connector-free (right picture above). The connector-free version includes a 14×1 straight 0.100" breakaway male header strip and two 3.5mm, 2-pin terminal blocks, but these parts are not soldered to the board, which allows for custom installations.
The three mounting holes are intended for use with #2 screws (not included).
|
|
||||
|
|
![]() |
Mounting Bracket for Concentric LD Linear Actuators |
![]() |
USB Cable A to Mini-B 6 ft. |
![]() |
Concentric LACT12P-12V-20 Linear Actuator with Feedback: 12" Stroke, 12V, 0.5"/s |
Data sheet
Manufacturer
Responsible person
A compact and powerful ESC speed controller designed for RC models and FPV racing, supporting 4S–8S LiPo batteries and a constant current of 60 A (instantaneous up to 70 A). With a 20x20 mm mounting standard, it ensures durability, reliability and easy integration even in limited space. The use of AM32 software and variable PWM frequency guarantees high precision and smooth operation of the motors in all conditions. F60A mini
Waveshare DDSM Driver HAT (B) is an advanced hub motor driver for DDSM400 motors, based on the ESP32, featuring both wired (USB, UART) and wireless (WiFi, ESP-NOW) communication. It supports control of up to 6 motors using JSON commands and integrates with Raspberry Pi, making it a suitable solution for mobile robotics and multi-motor system projects.
The dual-channel KAmod Motor Driver TB6612FNG with MOSFET H-bridges enables precise control of DC and stepper motors with PWM frequency up to 100 kHz. The compact design, wide voltage range, and protections make the module suitable for mobile projects, robotics, and automation.
This L298N module allows independent control of two DC motors or one stepper motor, ideal for robotics and DIY projects. It supports power supplies from 7V to 35V and has a built-in 5V regulator that can power additional circuits. Control is performed via the ENA, ENB, and IN1–IN4 pins, allowing for adjustable rotational direction and speed. The module is equipped with protection diodes and filter capacitors for stable and reliable operation.
An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous current up to 1.1 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4972
An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous currents up to 1.3 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4971
Bipolar stepper motor driver operating at voltages from 8 to 50 V and currents up to 8 A/phase (11 A with cooling). The DRV8711 driver with an SPI interface offers 9 stepping modes (up to 1/256), current configuration, stall detection, and protection against short circuits, overloads, and reverse polarity. Compatible with 1.8–5 V logic, it is ideal for CNC machines, 3D printers, and robotics. Pololu 3731
Driver board designed for DDSM series servo motors, featuring an ESP32 microcontroller, 2.4 GHz WiFi connectivity, RS485 and UART interfaces, and an integrated 5 V buck converter for powering a Raspberry Pi. Supports up to four DDSM115 or DDSM315 motors, or up to four DDSM210 motors, providing both wired and wireless control as well as JSON-based command support. DDSM Driver HAT (A)
This board allows for simultaneous control of two motors with full direction and stopping control, ideal for robotic buggies and educational vehicles. It features built-in short circuit, overload, and overheat protection, as well as a stabilized 3V output to power the micro:bit. The Edge Connector and additional pins allow for easy connection of sensors, switches, and accessories, expanding the project\'s functionality. Programming is supported by dedicated MakeCode blocks and support for the Kitronik 5698 Python.
Compact stepper motor driver based on the TMC5160-TA chip by Trinamic, designed for precise and quiet control of stepper motors in 3D printers, CNC machines, and other automation systems. The module operates with a motor supply voltage from 8 V to 35 V, providing high performance and stable operation thanks to advanced motion control algorithms. Communication is handled via the SPI interface, allowing precise configuration of operating parameters. The driver supports microstepping up to 1/256, ensuring very high motion precision and smooth motor operation. BIGTREETECH TMC5160T V1.0
This stepper motor driver offers microsteps down to 1/256th of a step, ensuring exceptional precision and smooth motion. Its simple operation—requiring only two microcontroller pins—and low operating voltage (1.8 to 10V) make it ideal for energy-efficient mobile, robotic, and DIY applications. Integrated connectors, LEDs, and a potentiometer for current adjustment facilitate prototyping and secure integration with popular platforms like Arduino and ESP32. Adafruit 6353
An H-bridge driver that provides bidirectional control of a high-power DC motor with a voltage range of 5-60 V and a continuous current of up to 11 A. The module supports PWM signals up to 100 kHz, features a current measurement (CS) output based on the ACS711 sensor, and features reverse polarity and short-circuit protection. It is compatible with both 3.3 V and 5 V logic, enabling easy integration with popular microcontroller platforms. Ideal for robotics, automation, and DIY projects requiring high performance and reliability. Pololu 2993
A speed controller based on the open VESC standard, designed for skateboards, scooters, and e-bikes. It supports voltages from 14 to 84 V (4S–20S) and continuous currents up to 100 A, offering various BLDC motor control modes and a wide range of interfaces (PPM, UART, I2C, USB-C, CAN). Its compact design, aluminum PCB, and extensive safety features ensure reliability, flexible configuration, and convenient integration with computers and smartphones. Makerbase VESC 75100 V2
This BLDC motor controller, based on the Allegro A89301 chip, enables sensorless control over a wide voltage range from 5.5 V to 48 V and phase current up to 11 A without additional cooling. It supports four control modes: analog voltage, PWM signal, pulse frequency, and via an I²C interface with the ability to configure parameters and save settings to EEPROM. The Field-Oriented Control (FOC) algorithm ensures quiet and efficient operation, while built-in protection protects the system against short circuits, reverse polarity, and undervoltage. Pololu 5357
This BLDC motor controller, based on the Allegro A89301 chip, enables sensorless control over a wide voltage range from 5.5 V to 48 V and phase current up to 11 A without additional cooling. It supports four control modes: analog voltage, PWM signal, pulse frequency, and via an I²C interface with the ability to configure parameters and save settings to EEPROM. The Field-Oriented Control (FOC) algorithm ensures quiet and efficient operation, while built-in protection protects the system against short circuits, reverse polarity, and undervoltage. Pololu 5356
A stepper motor driver for precise control of bipolar motors, offering six microstepping modes (from full to 1/32). It operates within a voltage range of 8.2V to 44V and delivers up to 1.5A per phase without cooling or up to 2.2A with a heatsink/fan, ensuring smooth and stable operation even at high speeds. Compatible with the popular A4988 and DRV8825 drivers, with an integrated regulator and overheating, overload, and short circuit protection, the TB67S581FNG is a reliable and versatile solution for applications requiring precise motion control. Pololu 2989
Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)