Cytron MD10-POT is a motor controller that allows you to easily control the speed and direction of a DC motor with a voltage in the range of 7-30 V and a current of up to 10 A. The set does not require a microcontroller. The motor can be controlled directly with a switch (activation and direction) and a potentiometer (speed). It is also possible to control the motor operation via the DIR and PWM inputs.
Example wiring

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The board is compatible with Arduino, based on the ATmega328P microcontroller from the AVR family, 14 I/O lines, 6 PWM channels, 6 analog inputs are available to the user. The CH340G chip communicates via a USB interface. In addition, it has 12 LEDs, a programmable button and a embedded buzzer. Cytron Uno Maker
Overlay compatible with Raspberry Pi Zero, Zero W, Zero WH, 1A+, 3A+, 3B, 3B+, 4B. Includes LEDs, buttons, USB-UART converter (USB connector) and buzzer. Cytron Maker pHAT
Dual DC motor controller with voltage from 2.5 to 9.5V with 1A continuous current per channel. Has an embedded voltage regulator. Cytron Maker Drive
Module with five reflection sensors. It has digital and analogue outputs. Thanks to the embedded EEPROM memory, it enables easy sensor calibration. Cytron Maker Line
No product available!
Single-channel DC motor controller that allows the motor to be controlled with a voltage range of 6-30V and a current of up to 20A. Allows engine speed control using PWM signals. MD20A cytron
Single-channel DC motor controller that allows the motor to be controlled with a voltage range of 6-30V and a current of up to 13A. Allows engine speed control using PWM signals. Cytron MD13S
Pololu Simple High-Power Motor Controller 18v25
No product available!
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1364
DC motor driver that allows you to control the movement of three drives using the I2C interface. Connectors for self-assembly. Pololu 5034
Two-channel driver for DC motors with an operating voltage from 7 to 35 V and a continuous current up to 10 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS10
No product available!
MP6550 DC motor controller module. It can work with motors supplied with voltage from 1.8 to 22 V and current consumption up to 1.7 A. Pololu 4733
Pololu High-Power Motor Driver 36v15
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5030
No product available!
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with connectors for mounting. Pololu 5065
No product available!
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader, and the board includes dual motor drivers that can deliver 1.7 A per channel to two brushed DC motors. Pololu 3119
Pololu Simple High-Power Motor Controller 24v23
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT