zł45.56 tax excl.
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
A DC motor controller that allows the movement of a single drive to be controlled via a I2C interface. It can operate with motors with supply voltages from 1.8 to 22 V and has a capacity of up to 1.8 A (continuous operation). The controller has built-in protection in case of loss of communication with the main controller and a configurable response if an error occurs. The user can set the maximum acceleration and initial speed of the motor Using a single I2C bus, it can control several modules. A user manual and a library with example programmes are available on the manufacturer's website.

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5076
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5038
No product available!
Pololu High-Power Motor Driver 36v15
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
No product available!
ESC type controller for a DC motor with a supply voltage of 3.7 V to 5 V. It offers a maximum output current of up to 1.5 A and allows you to control two motors independently
No product available!
A single-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. Board with soldered connectors. Pololu 5062
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5050
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5039
No product available!
Pololu Simple Motor Controller 18v7 (Fully Assembled)
Pololu Simple High-Power Motor Controller 24v23
No product available!
Two-channel DC motor driver communicating via UART, SPI or I2C interface. It can control the movement of 3 to 11V motors with a maximum continuous current of 1.2A per channel. SparkFun ROB-13911
No product available!
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14451
A two-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. Board with soldered connectors. Pololu 5066
No product available!
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751
No product available!
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075