New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
Motoron M1U550 Single Serial Motor Controller - DC motor controller (for assembly)
ID: 1185698
5902186316850
zł59.86
Tax included
zł48.67 tax excl.
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
Description
A DC motor controller that allows the movement of a single drive to be controlled via a UART TTL interface. It can operate with motors with supply voltages from 1.8 to 22 V and has a capacity of up to 1.8 A (continuous operation). The controller has built-in protection in case of loss of communication with the main controller and a configurable response if an error occurs. The user can set the maximum acceleration and initial speed of the motor Using a single UART bus, it can control several modules. A user manual and a library with example programmes are available on the manufacturer's website.
Features
- Operating voltage range: 1.8 V to 22 V
- Maximum output current per motor: 1.8 A continuous, 5 A instantaneous
- Voltage range of the logic part: 3 V to 5.5 V
- Control interface: UART TTL, up to 250 kbps
- CRC control possible
- Configurable motion parameters:
- Maximum acceleration/deceleration
- Initial speed
- Delay for change of direction
- PWM frequency: eight options from 1 kHz to 80 kHz available
- Protection in case of communication loss
- Configurable automatic error response
- Measurement of motor supply voltage (VIN)
- Two status LEDs
- Motor direction LEDs
- Dimensions: 15.24 x 15.24 mm
Kit contains
- Motoron M1U550 Single Serial Motor Controller
- Connector 1x12 straight male
1185698
Data sheet
- Output current
- 1,8 A
- Number of channels
- 1
- Supply voltage min
- 1,8 V
- Supply voltages max
- 22 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5076
zł68.14
24h
Available quantity: 2
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
zł56.04
24h
Available quantity: 1
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5074
zł68.14
24h
Available quantity: 2
Available
Other products in the same category (16)
Module with a 2-channel DC motor driver TB6612FNG designed to work with micro: bit. It can also control 3 servos. SB Components 14897
zł76.94
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5057
zł459.97
4 weeks
No product available!
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
zł76.48
24h
Available quantity: 2
Available
The DC motor driver module enables the motor to be controlled using a PWM signal with several supply voltages (3V, 6V, 12V, 24V and 35V) and a maximum continuous current of 5A.
zł7.81
24h
Available quantity: 15
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
4 weeks
No product available!
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and uses the PPM signal. DFRobot DFR0513
zł69.46
24h
Available quantity: 1
Available
A4990 Dual Motor Driver Carrier
zł44.97
24h
Available quantity: 1
Available
The module with the DRV8830 DC motor controller with a maximum current of 1 A. The board is equipped with a screw connector and communicates via the I2C interface. Pimoroni PIM479
Regular pricezł60.70zł48.56
24h
Available quantity: 12
Available
Dual H-Bridge motor driver board, 2A, 36V max, L298N, RoHS
zł12.60
24h
Available quantity: 12
Available
HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280
zł133.02
24h
Available quantity: 1
Available
A single-channel DC motor driver with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. A board with soldered connectors. Pololu 5060
zł89.05
4 weeks
No product available!
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
zł146.07
24h
Available quantity: 4
Available
ESC type controller for a DC motor with a supply voltage of 3.7 V to 5 V. It offers a maximum output current of up to 1.5 A and allows you to control two motors independently
zł60.61
4 weeks
No product available!
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
DC motor driver that allows you to control the movement of three drives using the I2C interface. Pololu 5035
zł179.27
24h
Available quantity: 2
Available
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
zł155.91
24h
Available quantity: 1
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077