.png)
MP6550 Single Brushed DC Motor Driver
ID: 1183959
5906623413294
zł27.29
Tax included
zł22.19 tax excl.
MP6550 DC motor controller module. It can work with motors supplied with voltage from 1.8 to 22 V and current consumption up to 1.7 A. Pololu 4733
Description
MP6550 DC motor controller module. It allows controlling the movement of a DC motor with a voltage from 1.8 to 22 V and a current of up to 1.7 A (continuous current). The interface requires two PWM control lines. The controller has built-in protection against reverse polarity, over voltage, overload and overheating. The logic part can be supplied with a voltage from 1.8 to 5 V, so the module can work with 3.3 V and 5 V.
Pinout:
- VIN - supply voltages 1.8 to 22 V
- GND - ground
- VM - pin giving access to motor supply voltage behind reverse polarity protection
- OUT1, OUT2 - motor outputs
- IN1, IN2 - PWM control signal
- SLEEP - input putting into low power mode
- ISET - configuration pin for current sensing and limiting. A 2 kΩ resistor is connected from this pin to ground
- VISEN - current sensor output. This pin provides an analog feedback voltage of 200 mV/A.
- V3P3 - 3.3 V output
Control interface
| IN1 | IN2 | OUT1 | OUT2 | Tryb pracy |
|---|---|---|---|---|
| 0 | 0 | Z | Z | outputs disabled |
| PWM | 0 | PWM (H/Z) | PWM (L/Z) | forward/reverse at PWM speed % |
| 0 | PWM | PWM (L/Z) | PWM (H/Z) | forward/reverse at PWM speed % |
| PWM | 1 | L | PWM (L/H) | reverse/brake at speed 100% − PWM % |
| 1 | PWM | PWM (L/H) | L | reverse/brake at speed 100% − PWM % |
| 1 | 1 | L | L | brake low (outputs shorted to ground) |
Features
- MP6550 motor controller
- Speed, direction control
- Motor supply voltage: 1.8 to 22 V
- Supply voltage of logic part: 1.8 to 5 V
- Motor current consumption: 1.7 A (continuous), 2.5 A (momentary)
- Protection against reverse polarity, over voltage, overload and overheating
- PWM interface
- Dimensions: 12.7 x 15.24 mm
Kit contains
- MP6550 Single Brushed DC Motor Driver
- 2 x 1x6 straight male connector
1183959
Data sheet
- Output current
- 1.7A
- Number of channels
- 1
- Supply voltage min
- 1,8 V
- Supply voltages max
- 22 V
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.90
24h
Available quantity: 208
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.48
24h
Available quantity: 396
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.10
24h
Available quantity: 488
Available
Other products in the same category (16)
Single-channel DC motor driver that can control the movement of the drive with a supply voltage of up to 36 V and a current consumption of up to 15 A. Controlled by a PWM signal. DFRobot DRI0042
zł129.97
24h
Available quantity: 2
Available
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
zł92.90
24h
Available quantity: 1
Available
The power module together with the engine controller has been specially created for the Romi Chassis chassis. With its help, we will supply all components of our construction and we will be able to control the engines responsible for the movement of the chassis. Pololu 3543
zł147.94
24h
Available quantity: 1
Available
Two-channel DC motor driver communicating via UART, SPI or I2C interface. It can control the movement of 3 to 11V motors with a maximum continuous current of 1.2A per channel. SparkFun ROB-13911
zł88.41
3 weeks
No product available!
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
zł119.35
24h
Available quantity: 1
Available
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
zł19.90
24h
Available quantity: 315
Available
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł51.18
1 weeks
No product available!
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
zł39.96
4 weeks
No product available!
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł302.73
24h
Available quantity: 2
Available
HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751
zł317.91
4 weeks
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł329.81
24h
Available quantity: 1
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł296.23
24h
Available quantity: 1
Available
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
zł419.89
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
zł405.67
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be powered with 6.5-30V and draw up a maximum current of 22A. Pololu 3754
zł379.64
4 weeks
No product available!
MP6550 DC motor controller module. It can work with motors supplied with voltage from 1.8 to 22 V and current consumption up to 1.7 A. Pololu 4733