Sterownik typu ESC do silnika DC, z miksowaniem kanałów

Module with the HR1124S DC motor controller with a maximum current of 1.2 A. It can be powered with the voltage from 1.8 V to 6.8 V and is controlled by two PWM signals

The core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader. This version does not include any through-hole components or connectors, allowing for customized assembly or standalone use. Pololu 3118

A single-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. Board with soldered connectors. Pololu 5062

DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584

Pololu G2 24v19 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 40V. Current efficiency of the module: 19A. The module has protection against back voltage and overvoltage. Pololu 1367

This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.

TB6612FNG Dual Motor Driver Carrier

HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751

Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B

Two-channel driver for DC motors with an operating voltage from 7 to 45 V and a continuous current of up to 60 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS60

An H-bridge driver that provides bidirectional control of a high-power DC motor with a voltage range of 5-60 V and a continuous current of up to 11 A. The module supports PWM signals up to 100 kHz, features a current measurement (CS) output based on the ACS711 sensor, and features reverse polarity and short-circuit protection. It is compatible with both 3.3 V and 5 V logic, enabling easy integration with popular microcontroller platforms. Ideal for robotics, automation, and DIY projects requiring high performance and reliability. Pololu 2993

A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with soldered connectors. Pololu 5064

Driver module for two DC brushed motors with current efficiency up to 5 A per channel. It can work with LiPo 2S and 3S packets

A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080

The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548

Module with 2-channel DC motor driver. It allows you to control the drive with a supply voltage from 3 to 11 V and a current of 1.2 A (1.5 A instantaneous). I2C communication. SparkFun ROB-15451