Module with controller of DC motors TB6612FNG for Wemos D1 Mini
ID: 1180538
5906623442898
zł45.61
Tax included
zł37.08 tax excl.
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
Description
A module with a two-channel DC motor driver based on the TB6612FNG system, designed for Wemos D1 Mini boards. They allow you to drive two DC motors with a voltage from 4.5 to 15 V and a continuous current of 1 A per channel. It uses the built-in STM32F030 microcontroller, which directly controls the H-bridge system. The module communicates via the I2C interface.
Features
- TB6612FNG chip
- Motor voltage: 4.5 to 15 V
- Logic voltage: 3.3 V
- Maximum output current (instantaneous): 3 A per channel
- Continuous output current: 1 A per channel
- Maximum PWM frequency: 100kHz
- I2C interface
- I2C address: 0x2D to 0x30
Kit contains
- Module with a driver of DC motors for Wemos D1
- 3 x 8-pin male goldpin connector
1180538
Data sheet
- Output current
- 1A
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 15 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Development board with dimensions and spacing compatible with Arduino Uno R3. It have built-in Wi-Fi ESP8266 module. The device is compatible with WeDOS D1, it can be programmed from the level of Arduino IDE
zł25.31
24h
Available quantity: 15
Available
Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini
zł19.36
24h
Available quantity: 18
Available
BMP180 temperature / pressure sensor module compatible with WeMos D1 mini board.
zł5.45
24h
Available quantity: 8
Available
Module with 0.66 "OLED display with 64x48 resolution for D1 Mini PCB with I2C interface. WeMos OLED Shield
zł12.87
24h
Available quantity: 5
Available
Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x
zł18.70
24h
Available quantity: 30
Available
Development board D1 Mini Pro with WiFi ESP8266 module and 16 MB Flash memory, equipped with ceramic antenna and external antenna connector. The module can be programmed from the Arduino IDE level. WeMos D1 Mini Pro
zł25.71
24h
Available quantity: 14
Available
Other products in the same category (16)
Pololu High-Power Motor Driver 18v15
zł283.71
4 weeks
No product available!
Two-channel driver for DC motors with an operating voltage from 7 to 35 V and a continuous current up to 10 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS10
zł278.32
24h
Available quantity: 1
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5074
zł68.14
24h
Available quantity: 2
Available
HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10
zł117.32
24h
Available quantity: 1
Available
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
zł86.42
24h
Available quantity: 2
Available
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
zł423.01
4 weeks
No product available!
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
zł460.81
24h
Available quantity: 1
Available
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
zł56.70
24h
Available quantity: 2
Available
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
zł225.57
24h
Available quantity: 1
Available
A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with soldered connectors. Pololu 5064
zł125.29
4 weeks
No product available!
HAT with TB6612FNG engine controller and PCA9685 PWM controller designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector characteristic of Raspberry Pi, making it compatible with all minicomputers with this connector. Waveshare Motor Driver HAT
zł67.00
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5045
zł456.85
4 weeks
No product available!
Module with DC motor driver DRV8256E. It can work with motors supplied with the voltage from 4.5 to 48 V and the current consumption up to 1.9 A. Pololu 4038
zł72.59
24h
Available quantity: 2
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
zł59.86
24h
Available quantity: 2
Available
TB9051FTG Single Brushed The DC Motor Driver Carrier is a single DC motor driver that allows the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption at a continuous 2.6 A (5A peak) operation. Pololu 2997
zł47.04
24h
Available quantity: 1
Available
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT
zł54.49
24h
Available quantity: 42
Available
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini