Two-channel motor controller (H-bridge) with L298N

Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036

ESC type controller for a DC motor with a supply voltage of 3.7 V to 5 V. It offers a maximum output current of up to 1.5 A and allows you to control two motors independently

BOB-11890

DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1

Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517

DC motor driver with a working voltage from 5 to 30 V and a maximum continuous current of 13 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD10C

DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584

DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5041

DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5058

Two-channel DC motor driver communicating via UART, SPI or I2C interface. It can control the movement of 3 to 11V motors with a maximum continuous current of 1.2A per channel. SparkFun ROB-13911

This board allows for simultaneous control of two motors with full direction and stopping control, ideal for robotic buggies and educational vehicles. It features built-in short circuit, overload, and overheat protection, as well as a stabilized 3V output to power the micro:bit. The Edge Connector and additional pins allow for easy connection of sensors, switches, and accessories, expanding the project\'s functionality. Programming is supported by dedicated MakeCode blocks and support for the Kitronik 5698 Python.

Pololu Jrk 21v3 USB Motor Controller with Feedback

An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous current up to 1.1 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4972

This compact breakout board is for ROHM’s BD65496MUV motor driver, which offers an operating voltage range of 2 V to 16 V and can deliver a continuous 1.2 A to a single brushed DC motor. Pololu 2960

Two-channel DC motor driver with an operating voltage from 7 to 35 V and a maximum continuous current of 30 A. It can be controlled by an analog signal, PWM, UART, RC signal or by means of built-in buttons. Cytron MDDS30

This add-on board enables a Raspberry Pi B+, Pi A+, Pi 2 or Pi 3 to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor. The default pin mappings make it easy to get started using our provided software, but the board also exposes most of the driver chips’ I/O pins for more specialized applications.