Motoron M2U550 Dual Serial Motor Controller - 2-channel DC motor controller (for assembly)
ID: 1185694
5902186316812
zł78.95
Tax included
zł64.19 tax excl.
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081
Description
A DC motor controller that allows the movement of two drives to be controlled via a UART TTL interface. It can operate with motors with supply voltages from 1.8 to 22 V and has a capacity of up to 1.6 A per motor (continuous operation). The controller has built-in protection in case of loss of communication with the main controller and a configurable response if an error occurs. The user can set the maximum acceleration and initial speed of the motor Using a single UART bus, it can control several modules. A user manual and a library with example programmes are available on the manufacturer's website.
Features
- Operating voltage range: 1.8 V to 22 V
- Maximum output current per motor: 1.6 A continuous, 5 A instantaneous
- Voltage range of the logic part: 3 V to 5.5 V
- Control interface: UART TTL, up to 250 kbps
- CRC control possible
- Configurable motion parameters:
- Maximum acceleration/deceleration
- Initial speed
- Delay for change of direction
- PWM frequency: eight options from 1 kHz to 80 kHz available
- Protection in case of communication loss
- Configurable automatic error response
- Measurement of motor supply voltage (VIN)
- Two status LEDs
- Motor direction LEDs
- Dimensions: 15.24 x 20.32 mm
Kit contains
- Motoron M2U550 Dual Serial Motor Controller
- Connector 1x16 straight male
1185694
Data sheet
- Output current
- 1,6 A
- Number of channels
- 2
- Supply voltage min
- 1,8 V
- Supply voltages max
- 22 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080
zł86.42
24h
Available quantity: 2
Available
A two-channel DC motor controller with a I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5079
zł73.46
24h
Available quantity: 1
Available
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
zł86.42
24h
Available quantity: 2
Available
Other products in the same category (16)
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5047
zł406.69
4 weeks
No product available!
Pololu High-Power Motor Driver 24v20
zł221.29
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5038
zł302.09
4 weeks
No product available!
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Pololu High-Power Motor Driver 36v20 CS
zł527.15
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5040
zł327.65
4 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł216.36
24h
Available quantity: 1
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5037
zł327.65
4 weeks
No product available!
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
zł146.80
4 weeks
No product available!
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
zł34.71
24h
Available quantity: 2
Available
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 4 to 16 V and a maximum continuous current of 3 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD3A
zł35.01
24h
Available quantity: 9
Available
The module with a 4-channel L293D DC motor driver, designed to work with the Raspberry Pi. It can work with a voltage from 6 to 24 V and a current of up to 600 mA. SB Components 08001
zł78.55
24h
Available quantity: 2
Available
Pololu Simple Motor Controller 18v7
zł746.97
4 weeks
No product available!
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081