List of products by brand Kamami

Module with 8 LEDs

The LM4950 audio power amplifier module with a power of 3 W per channel, powered by 10-15 VDC, equipped with a 3.5 mm Jack socket for audio input and screw connections for loudspeaker outputs, is equipped with thermal and short-circuit protection. It provides good sound quality with low energy consumption, making it ideal for small audio systems

KA-NUCLEO-F411CE v2 is a development board based on the STM32F411CE microcontroller. It has a built-in programmer compatible with ST-Link / v2-1, it is possible to program and debug the microcontroller via the USB connector.

Easy-to-use retractable cable with USB type A plugs and mini-B type, the cable is 73 cm long after being unrolled

KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05

T-Cobbler adapter enabling connection of GPIO Raspberry Pi A +, B +, Pi 2, Pi 3, Pi 4 and Pi 5 lines to the breadboard (2.54 mm). Adapter assembled, included connecting tape

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at a frequency of 133 MHz, 264 kB RAM. There is as much as 16 MB of QSPI flash memory on the board. The system can be programmed in C / C ++ or microPython. Soldered connectors. KApico RP2040

Versatile CAN bus interface based on the MCP2518FD controller, enabling communication in CAN 2.0 and CAN FD modes via SPI interface, compatible with SBC computers, including Raspberry Pi 5, with additional security and the ability to support two modules simultaneously

This universal expansion board for the Raspberry Pi Pico extends GPIO pins to both male and female goldpin connectors and screw terminals with labeled pins, facilitating and accelerating prototyping without the need for soldering

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at a frequency of 133 MHz, 264 kB RAM. There is as much as 16 MB of QSPI flash memory on the board. The system can be programmed in C / C ++ or microPython. KApico RP2040

TTL - RS485 converter 5V. RS485 interface on 5.08mm screw terminal and 2.54mm pitch connector.

Module of a stereo 24-bit audio converter with I2S interface (TS4657).

Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer

Module with Nokia 6100/6610 color graphic LCD

Simulation set for Siemens S7-1200 PLC devices. Using this set, it is possible to verify the operation of a program written for a PLC by applying the appropriate states to the digital inputs, to the analogue (ADC) inputs voltages from the built-in or external sensors. LED status monitoring is possible

KA-LOGO! -IO-Simulator is a simulation set for the Siemens LOGO logic controller! 8. Using this set, it is possible to simulate individual bits at the controller inputs as well as using the ADC converter embedded in the controller. In addition, the module with LEDs allows signaling of states on four outputs of the logic controller

Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function

RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming

Programmable RGB and RGBA LED driver

Universal minicomputer with STM32F103C6 microcontroller (ARM Cortex-M3 @72 MHz, 32 kB Flash, 10 kB RAM, LQFP48 package)