

Pololu Simple Motor Controller 18v7
The Pololu Simple Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 7 A (>30 A peak) without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations.
![]() |
Simple Motor Controllers. |
---|
The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in a small form factor make these controllers suitable for many motor control applications. With a variety of supported interfaces—USB for direct connection to a computer, TTL serial for use with embedded systems, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), and analog voltages for use with a potentiometer or analog joystick—and a wide array of configurable settings, these motor controllers make it easy to add basic control of brushed DC motors to a variety of projects. Although this motor controller has many more features than competing products, a free configuration utility (for Windows 7, Vista, Windows XP, and Linux) simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB.
For 24 V applications, we recommend the 24v12 or 24v23 versions. We strongly recommend against using the 18v7, 18v15, or 18v25 with 24 V batteries, which can significantly exceed 24 V when fully charged and are dangerously close to the maximum voltage limits of these lower-voltage controllers.
![]() |
Simple High-Power Motor Controller 18v25 or 24v23 simplified connection diagram. |
---|
|
|
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
Two Pololu Simple Motor Controllers enable mixed RC-control of Dagu Wild Thumper 4WD all-terrain chassis. |
---|
The Simple Motor Controllers are available in several input voltage ranges and output current ranges:
![]() 18v7 | ![]() 18v15 | ![]() 24v12 | ![]() 18v25 | ![]() 24v23 | |
---|---|---|---|---|---|
Absolute max voltage: | 30 V | 30 V | 40 V | 30 V | 40 V |
Recommended max voltage(1): | 24 V | 24 V | 34 V | 24 V | 34 V |
Max continuous current w/o heat sink: | 7 A | 15 A | 12 A | 25 A | 23 A |
Width: | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.2" (3.1 cm) | 1.2" (3.1 cm) |
Length: | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.3" (5.8 cm) | 2.3" (5.8 cm) |
Weight(2): | 7 g | 7 g | 7 g | 12 g | 12 g |
Available with connectors installed? | Yes | Yes | Yes | No | No |
1 We do not recommend using the 18v7, 18v15, or 18v25 versions with 24 V batteries, which can significantly exceed 24 V when fully charged. The 24v12 and 24v23 are the much more appropriate controller for 24 V applications.
2 This is the weight of the board without header pins, terminal blocks, or through-hole power capacitor.
|
|
Most Simple Motor Controllers are available “fully assembled”, with the power capacitor and connectors pre-installed, or with these components included but not soldered in. For example, a fully assembled 18v15 ships as shown in the left picture above, and an 18v15 with included hardware ships as shown in the right picture above (the included hardware consists of a power capacitor, a 40×1 straight 0.1" male header strip, a 5mm-pitch 4-pin terminal block, and a blue shorting block).
The connector-free version allows flexibility in choice of connectors and placement of the power capacitor (e.g. on the other side of the board) to accommodate compact installations or to make room for a heat sink.
Note: The power capacitor has a significant effect on performance; the included capacitor is the minimum size recommended, and bigger ones can be added if there is space. A bigger capacitor might be required if the power supply is poor or far (more than about a foot) from the controller.
The included terminal blocks are only rated for 16 A, so we recommend soldering thick wires directly to the connector-free version of the board and using higher-current connectors for applications that will exceed the terminal blocks’ ratings.
|
|
|
Warning: Take proper safety precautions when using high-power electronics. Make sure you know what you are doing when using high voltages or currents! During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.
![]() |
USB Cable A to Mini-B 6 ft. |
![]() |
Pololu Universal Aluminum Mounting Hub for 6mm Shaft Pair, 4-40 Holes |
Cechy
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka z przylutowanymi złączami. Pololu 5036
Brak towaru
Sterownik silników krokowych, oferujący mikroki aż do 1/256 kroku, co zapewnia wyjątkową precyzję i płynność ruchu. Dzięki prostej obsłudze – wymagającej jedynie dwóch pinów z mikrokontrolera – oraz niskim napięciu pracy (1,8 do 10 V), doskonale nadaje się do energooszczędnych aplikacji mobilnych, robotycznych i DIY. Zintegrowane złącza, diody LED i potencjometr do regulacji prądu ułatwiają prototypowanie i bezpieczną integrację z popularnymi platformami takimi jak Arduino czy ESP32. Adafruit 6353
Sterownik silnika krokowego AMIS-30543 operujący w zakresie napięć 6..30 V i prądzie 1,8 A. Pololu 2970
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka bez złączy. Pololu 5038
Brak towaru
Pololu Dual G2 High-Power Motor Driver 18v18 to rozszerzenie pozwalające na sterowanie dwoma silnikami prądu stałego przeznaczone dla Raspberry Pi. Silniki mogą być zasilane napięciem 6,5-30V i pobierać maksymalnie prąd o natężeniu do 18A. Pololu 3750
Dwukanałowy sterownik silników DC z interfejsem I2C. Jest zasilany napięciem od 4,5 V do 48 V i może dostarczyć prąd o natężeniu do 1,8 A na silnik. Płytka z przylutowanymi złączami. Pololu 5064
Brak towaru
Sterownik silników używający Serial portu do komunikacji z mikrokontrolerem. Sparkfun ROB-09571
Dwukanałowy sterownik silników DC o napięciu pracy od 7 do 35 V i prądzie ciągłym do 10 A. Może być sterowany sygnałem analogowym, PWM, UART, RC lub za pomocą wbudowanych przycisków. Cytron MDDS10
Dwukanałowy sterownik silników DC z interfejsem UART TTL. Jest zasilany napięciem od 4,5 V do 48 V i może dostarczyć prąd o natężeniu do 1,8 A na silnik. Płytka ze złączami do montażu. Pololu 5067
Brak towaru
Sterownik silników krokowych, który może pracować z napięciem z zakresu od 24 do 110 VDC lub od 18 do 80 VAC oraz maksymalnym prądem do 8,4 A. Umożliwia konfigurację mikro kroku w zakresie od 2 do 256. 2DM860H
Miniaturowy sterownik typu ESC do silnika DC o napięciu zasilania od 3,7 V do 5 V. Oferuje maksymalny prąd wyjściowy do 1,5 A i pozwala na sterowanie dwoma silnikami w trybie miksowania kanałów
Sterownik silnika krokowego A4988 operujący na napięciach 8..35 V i prądzie 1,2 A. Pololu 2128
Pololu High-Power Motor Driver 18v15
Brak towaru
X-NUCLEO-IHM02A1 to moduł sterownika dwóch silników krokowych oparty na dwóch układach L6470. Poziom logiczny 3,3 lub 5 V, sterowanie przez SPI. Złącza zgodne z Arduino i STM32 Nucleo
Moduł sterownika dwóch silników szczotkowych DC o wydajności prądowej do 5 A na kanał. Może współpracować z pakietami LiPo 2S i 3S
Moduł ze sterownikiem silników TB6612FNG oraz sterownikiem PWM PCA9685 dla Raspberry Pi Pico. Pozwala na kontrolowanie ruchu 4 silników DC. Waveshare Pico-Motor-Driver
Pololu Simple Motor Controller 18v7