- Obecnie brak na stanie
![Pololu 2110 - Pololu Step-Down Voltage Regulator D15V35F5S3 Pololu 2110 - Pololu Step-Down Voltage Regulator D15V35F5S3](https://kamami.pl/8110-large_default/pololu-2110-pololu-step-down-voltage-regulator-d15v35f5s3.jpg)
Pololu Step-Down Voltage Regulator D15V35F5S3
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
Pololu Step-Down Voltage Regulator D15V35F5S3
The compact (1.68"×0.46") D15V35F5S3 switching step-down (or buck) voltage regulator takes an input voltage between 4.5 and 24 V and efficiently reduces it to a lower, user-selectable voltage. The selectable output voltages are 5 and 3.3 V, and it can deliver up to 3.5 A continuous in typical applications.
![]() |
These buck (step-down) voltage regulators from Pololu generate lower, user-selectable output voltages from an input voltage range of 4.5 to 24 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical (when the output current is several amps) efficiency of approximately 90%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. The output voltage defaults to 5 V and can be changed to 3.3 V by jumping 3V3 SEL.
The regulator has under-voltage and short-circuit protection, and thermal shutdown prevents damage from overheating. The board has reverse-voltage protection.
We offer two versions of these higher-current step-down regulators:
We also offer four lower-current step-down voltage regulators:
![]() |
Pololu step-down voltage regulator D15V35F5S3 with included hardware. |
---|
The buck regulator has five connections: 3.3 V select (3V3 SEL), enable (EN), input voltage (VIN), ground (GND), and output voltage (VOUT).
The EN pin can be driven low (under 0.3 V) to turn off the output and put the board into a low-power state that typically draws 150 ěA. The board has a 100kΩ pull-up resistor between EN and VIN. The EN pin can be driven high (above 2 V) to enable the board, or it can be connected to VIN or left disconnected if you want to leave the board permanently enabled.
The input voltage, VIN, should be between 4.5 and 24 V. You should ensure that noise on your input does not exceed the 24 V maximum. When power is applied, the input voltage rise time must not be more than a few milliseconds; otherwise, the regulator can latch in an error state that disables its output.
The output voltage, VOUT, is determined by the 3V3 SEL jumper state. If the jumper is disconnected, the output voltage is 5 V. With the jumper connected, the output voltage is 3.3 V. An input voltage lower than the output voltage will not damage the board, but will cause a lower-than-selected output voltage, so we recommend you avoid powering the board with an input voltage below the selected output voltage.
Warning: Do not change the 3V3 SEL jumper while the regulator is powered. Doing so can cause the regulator to shut off until power is cycled.
The connections are labeled on the back side of the PCB. The eight smaller through-holes on the ends of the board are arranged with a 0.1" spacing for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1" grid. You can solder wires directly to the board or solder in either the 10?1 straight male header strip or the 2 terminal blocks that are included.
The regulator’s over-current protection limits the output current of the board to 4.5 A. However, over-temperature protection will typically kick in at lower output currents. Therefore, the maximum achievable output current of the board depends on many factors, including the ambient temperature, air flow, heat sinking, and the input voltage. In our tests at room temperature, a continuous output current of 3.5 A was available across the entire input voltage range. These continuous current characteristics are limited by thermal dissipation; the regulator can output higher currents for several seconds or even tens of seconds, depending on how low the current is during the off-peak periods. Higher continuous output current can be achieved by reducing the input voltage or by cooling the board by adding a heat sink or a fan.
During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.
The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, this switching regulator typically has an efficiency of 80 to 90%. For example, when regulating 12 V to 5 V with an output current of 1.8 A, the efficiency is 90%. Since the output power is (Output current)?(Vout) = 1.8 A ? 5 V = 9 W, the input power will be 10 W, with 1 W of heat dissipated in the regulator. The input current can then be calculated as 10 W/12 V = 0.83 A. This is far better than a linear voltage regulator, which would require an input current of 1.8 A and 22 W, wasting 13 W instead of the 1 W lost in this switching regulator.
![]() |
![]() |
![]() |
Pololu Step-Up/Step-Down Voltage Regulator S8V3A |
![]() |
Pololu Step-Down Voltage Regulator D15V70F5S3 |
![]() |
Pololu Step-Down Voltage Regulator D24V6ALV |
UGears Bursztynowa Szkatułka to idealny prezent dla kogoś wyjątkowego lub cenna ozdoba do własnej kolekcji. Łączy w sobie piękno naturalnego bursztynu, kunszt mechanicznej precyzji i funkcjonalność eleganckiego pudełka do przechowywania. UGears 70090
Brak towaru
Brak towaru
Wyświetlacz LCD IPS 4" z ekranem dotykowym. Wyświetlacz jest wyposażony w interfejs DPI do wyświetlania obrazu oraz I2C do ekranu dotykowego. Rozdzielczość 800x480 pikseli. Waveshare 4inch DPI LCD (B)
Brak towaru
Brak towaru
SYGNALIZATOR LED - ZESTAW DO SAMODZIELNEGO MONTAŻU
Brak towaru
Zmontowany sterownik zasilania taśm LED z wyłącznikiem czasowym. AVT1867 C
Brak towaru
Wyświetlacz graficzny128x48, 96x44mm, podświetlanie LED, rozszerzony zakres temperatury, kontroler: KS0108, 3V
Brak towaru
Tulejka dystansowa walcowa o średnicy wewnętrznej 3.3mm i zewnętrznej 5mm, długość tulejki 25mm. Tulejka wykonana z nylonu. Zestaw zawiera 10 sztuk. Pololu 1988
Brak towaru
Brak towaru
Moduł z układem dwukierunkowego konwertera poziomów logicznych PCA9306, konwersja 1.0-3.6V oraz 1.8-5.5V, komunikacja poprzez interfejs I2C oraz SMB. SparkFun BOB-11955
Brak towaru
MEMS inertial sensor 3-axis, low g accelerometer with digital output, QFN28, STM, RoHS
Brak towaru
Przewód z wtykami USB typu A, microUSB typu B, Lightning oraz USB typu C pozwalający jedynie na ładowanie, długość przewodu 1,8 m. LANBERG
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Pololu Step-Down Voltage Regulator D15V35F5S3