This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.

An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4873

Female-female cable, 16 cm long, with JST-SH 6-pin plug on both sides. Suitable for micro DC motor encoders with gear. Pololu 4766

Efficient step-down converter that reduces the input voltage from up to 45 V to a regulated output voltage range from 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in protection against reverse polarity, overload and short circuit, and the spread spectrum function reduces EMI interference. The module is equipped with an additional potentiometer for adjusting the cut-off voltage. Pololu 4872

ACS724LLCTR-30AB current sensor module with a DC and AC measurement range from -30 to +30 A. It communicates via an analog interface. Pololu 4047

ACS724LLCTR-10AB current sensor module with a DC and AC measurement range from -10 to +10 A. It communicates via an analog interface. Pololu 4043

Efficient step-down converter that reduces the input voltage from up to 45 V to a regulated output voltage range from 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.8 A. It has built-in protection against reverse polarity, overload and short circuit, and the spread spectrum function reduces EMI interference. The module is equipped with an additional potentiometer for adjusting the cut-off voltage. Pololu 4852

This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor.

Pololu - 3498

A4988 Stepper Motor Driver Carrier

Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8° per step), rated voltage of 3.8 V, and has a current consumption of 0.67 A per coil. Pololu 1205

A-Star 328P Micro is a small board based on ATmega 328PB microcontroller (Flash, 32 KB, SRAM, 2.5 KB, EEPROM, 1KB, 8 MHz). The system has a loaded bootloader compatible with Arduino. The board has 24 I / O ports (of which 9 pins can be used for PWM outputs and 8 pins for analog inputs). Supply voltage 3.8-15 V. The board works with 3.3 V voltage. Pololu 3162

An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.8 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4853

Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8° per step), has a nominal voltage of 4 V and draws a current of 1.2 A per coil. Pololu 1200

Magnetic disk for use with magnetic encoders designed for Pololu 20D series motors. It allows you to generate 12 pulses per revolution. Pololu 3449

DC-DC Step-Up/Step-Down Converter Module. It has an input voltage of 1.4 to 16 V, an output voltage of 5 V and a maximum output current of 1 A to 1.5 A. Pololu 4965

Module with a stepper motor driver based on the DRV8834 system. It allows you to power a bipolar motor with a current of up to 2 A per phase, without using a heat sink. The system can be powered with a voltage of up to 10.8 V. Pololu 2134

Miniature, 6V brush DC motor with metal gear with 15,25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft has a length of 10 mm and a diameter of 3 mm. Pololu 4787

The compact (0.4″ × 0.5″) D24V5F1 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 1.8 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 75% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

This RC switch converts hobby radio control pulses to digital on/off signals for use in RC switch and simple RC adapter applications. One output indicates the presence of a valid RC signal, and the other indicates whether the switch is active. The activation threshold and direction are configurable, and a safe-start feature reduces the likelihood of unexpected activation. Pololu 2801