![Main view Main view](https://kamami.pl/80469-large_default/acs724-current-sensor-carrier-30a-to-30a.jpg)
![Main view Main view](https://kamami.pl/80469-large_default/acs724-current-sensor-carrier-30a-to-30a.jpg)
zł42.57 tax excl.
ACS724LLCTR-30AB current sensor module with a DC and AC measurement range from -30 to +30 A. It communicates via an analog interface. Pololu 4047
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Module with a two-way Hall current sensor based on the ACS724LLCTR-30AB chip. It allows you to measure the current in the range from -30 to 30 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (66 mV/A) centered at 2.5 V with an error of ± 0,8%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
No product available!
Module with INA228 sensor designed for power monitoring. It allows you to measure voltages up to 85 VDC and currents up to 10 A. It uses a 20-bit ADC converter, which guarantees very precise and accurate measurements available via the I2C bus. Adafruit 58332
No product available!
Power monitor module that detects voltages up to 60 VDC and current up to 30 A. It uses the Allegro MicroSystems ACS37800 IC, which simplifies adding monitoring to power systems. SparkFun SPX-17873
No product available!
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 45 A. SparkFun SEN-16407
No product available!
Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262
Module with ACS723 current sensor with a measuring range of AC and DC ± 5 A. It communicates via an analog interface. SparkFun SEN-13679
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
No product available!
INA169 current sensor module. The system can be supplied with the voltage from 2.7 V to 60 V and has an analog output. SparkFun SEN-12040
Analogue current sensor module. Allows measurement of AC and DC currents up to 50 A. DFRobot SEN0098-V2
The module with the ACS70331 current sensor with a direct and alternating current measuring range ±5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020615
ACS714 Current Sensor Carrier -5 to +5A
ACS724LLCTR-30AB current sensor module with a DC and AC measurement range from -30 to +30 A. It communicates via an analog interface. Pololu 4047