ACS724 Current Sensor Carrier - module with ACS724 ±5A current sensor
ID: 586599
5906623480470
zł47.71
Tax included
zł38.79 tax excl.
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with a two-way Hall current sensor based on the ACS724LLCTR-05AB chip. It allows you to measure the current in the range from -5 to 5 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (400 mV/A) centered at 2.5 V with an error of ± 1.5%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -5 to 5 A
- Output resolution 0.4 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
586599
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±5 A
- Sposób podłączenia
- Szeregowy
You might also like
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł89.19
24h
Available quantity: 2
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.01
24h
Available quantity: 867
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł3.94
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.62
Delivery date unknown
No product available!
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł81.72
24h
Available quantity: 3
Available
Other products in the same category (16)
ACS724LLCTR-05AU current sensor module with a current measurement range from 0 to 5 A. It communicates via an analog interface. Pololu 4048
zł53.84
24h
Available quantity: 3
Available
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030
zł16.63
24h
Available quantity: 5
Available
Available
Module with INA228 sensor designed for power monitoring. It allows you to measure voltages up to 85 VDC and currents up to 10 A. It uses a 20-bit ADC converter, which guarantees very precise and accurate measurements available via the I2C bus. Adafruit 58332
zł82.05
24h
Available quantity: 2
Available
ACS723 current sensor module with a DC and AC measuring range of ± 5 A. It can read very low currents of 10 mA. It communicates via the analog interface. SparkFun SEN-14544
zł117.16
4 weeks
No product available!
This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034
zł35.65
24h
Available quantity: 4
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł6.91
6 weeks
No product available!
The module with the ACS70331 current sensor with a direct current measuring range up to 2,5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020652
zł48.34
24h
Available quantity: 1
Available
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 2
Available
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.18
24h
Available quantity: 13
Available
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
zł34.26
24h
Available quantity: 6
Available
Power monitor module that detects voltages up to 60 VDC and current up to 30 A. It uses the Allegro MicroSystems ACS37800 IC, which simplifies adding monitoring to power systems. SparkFun SPX-17873
zł179.00
6 weeks
No product available!
Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032
zł17.86
24h
Available quantity: 5
Available
A digital precision current sensor module that measures voltage, current and power of electronic modules and devices up to 26V and 8A with a relative error of ± 0.2%. DFRobot SEN0291
zł32.15
24h
Available quantity: 5
Available
Analogue current sensor module. Allows measurement of AC and DC currents up to 50 A. DFRobot SEN0098-V2
zł73.89
24h
Available quantity: 1
Available
Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262
zł23.48
24h
Available quantity: 11
Available
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041