ACS37041KLHBLT-030B5 Current Sensor - module with current sensor -30A to +30A, 5V
ID: 1197867
5902186322295
zł15.89
Tax included
zł12.92 tax excl.
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 66.7 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5443
Description
ACS37041 Micro Carrier is a compact module based on the Allegro ACS37041KLHBLT-030B5 current sensor, using Hall effect technology and providing galvanic isolation for measurements. The device features a very low current path resistance of ~1.6 mΩ, minimizing energy loss and ensuring high accuracy for both DC and AC current measurements. The analog output offers a wide 150 kHz bandwidth, allowing fast and precise current measurement in dynamic circuits. The sensor response time is less than 5 µs, making it ideal for applications requiring rapid response.
The module has five essential pins: current inputs IP+ and IP-, logic supply VDD and GND, and signal output VOUT. Power should be connected to the VDD and GND pads marked on the bottom of the board. The VOUT output generates an analog signal with a resting voltage of 2.5 V, which changes proportionally to the input current. Positive current increases the output voltage, while negative current decreases it, with a sensitivity of 66.7 mV/A.
The board can be integrated into the current path in various ways depending on the application. In typical high-current applications, wires can be soldered directly to the mounting holes. These holes are also compatible with screw terminals with 3.5 mm or 5 mm spacing, simplifying module installation in prototype and final setups. Alternatively, goldpin connectors can be used.
The sensor offers integrated temperature compensation, increasing accuracy across the full operating range of -40°C to 125°C, according to automotive standards. The device is non-ratiometric, meaning its zero point and sensitivity are independent of supply voltage fluctuations, ensuring noise immunity. The module operates at 4.5 V to 5.5 V and supports a bidirectional measurement range of -30 A to +30 A. Its compact size makes it suitable for compact projects.
Features
- Sensor: ACS37041KLHBLT-030B5
- Measurement range: ±30 A (bidirectional)
- Supply voltage: 4.5 V to 5.5 V (nominal 5 V)
- Sensitivity: 66.7 mV/A
- Zero point: 2.5 V
- Current path resistance: ~1.6 mΩ
- Bandwidth: 150 kHz
- Response time: < 5 µs
- Temperature compensation
- Operating temperature: -40°C to 125°C
- Galvanic isolation
- Dimensions: 7.6 × 10.2 mm
1197867
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±30 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł1.23
24h
Available quantity: 5129
Available
Pin header goldpin black 1x40 pins. Angled connector for through-hole assembly. 2.54mm pitch.
zł1.23
24h
Available quantity: 19246
Available
2-pin ARK mounting strip, 3.5 mm pitch. 381-3.5-02P-14-00AH
Delivery date unknown
No product available!
2-pin ARK mounting strip, 3.5 mm pitch. 381-3.5-02P-14-00AH. Set of 10 pieces
zł7.23
24h
Available quantity: 8
Available
Other products in the same category (16)
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5244
zł22.15
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5256
zł56.70
24h
Available quantity: 2
Available
A modern current sensor combining the Hall effect with an inductive coil, which allows for precise measurements of both the DC and AC components up to 5 MHz. Thanks to its lightning-fast response time and low path resistance, it is perfect for motor control systems, power converters and protection systems. Pololu 5235
zł63.04
24h
Available quantity: 2
Available
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5246
zł21.37
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5257
zł58.79
24h
Available quantity: 2
Available
Module with an analog current sensor. It enables the measurement of AC and DC current up to 50 A. DFRobot SEN0098
zł134.91
4 weeks
No product available!
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. Pololu 5410
zł133.97
4 weeks
No product available!
Analogue current sensor module. Allows measurement of AC and DC currents up to 50 A. DFRobot SEN0098-V2
zł73.42
24h
Available quantity: 2
Available
Compact current sensor based on TMR technology, enabling precise measurements up to 20 A with minimal energy losses. Thanks to a wide 1 MHz bandwidth, galvanic isolation and interference immunity, it is perfect for applications requiring fast response and high accuracy. Pololu 5316
zł52.79
4 weeks
No product available!
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5241
zł22.16
24h
Available quantity: 3
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5447
zł17.10
4 weeks
No product available!
A modern current sensor with a measurement range of -40 A to +40 A, combining the Hall effect with an inductor, allows for precise measurements of both DC and AC components up to 5 MHz. Its lightning-fast response time and low path resistance make it ideal for motor control systems, power converters, and protection systems. Pololu 5234
zł56.49
6 weeks
No product available!
Module with INA228 sensor designed for power monitoring. It allows you to measure voltages up to 85 VDC and currents up to 10 A. It uses a 20-bit ADC converter, which guarantees very precise and accurate measurements available via the I2C bus. Adafruit 58332
zł74.26
4 weeks
No product available!
ACS711EX Current Sensor Carrier -31A to +31A
zł21.50
4 weeks
No product available!
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045
zł44.72
4 weeks
No product available!
The ACS72981 current sensor module uses the Hall effect to precisely and safely measure DC current while providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes power loss and offers a fast response time of less than 2 µs. Pololu 5284
zł64.33
24h
Available quantity: 2
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 66.7 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5443