CT432-HSWF30DR TMR Current Sensor - current sensor module 0-30A, 5V

This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. The version comes with soldered screw terminals and a 240 Vrms jumper. Pololu 5412

The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5271

Allegro\'s TMR sensor module enables precise, non-contact current measurement without breaking the circuit. It offers high sensitivity, low power consumption, an analog output proportional to the magnetic field, and a threshold detection (FLAG) function. Its compact design, AC/DC support, and easy installation make it ideal for energy-efficient and safe current monitoring systems. Pololu 5355

Compact Pololu 5292 current sensor based on the ACS37220 IC, designed for measuring currents up to ±100 A at a 5 V supply voltage in applications requiring galvanic isolation and an analog output. Pololu 5292

Crowtail – Current Sensor 2.0 enables AC/DC current measurement up to ±20 A using the ACS712 chip and generates an analog signal for further analysis. Used in energy-consumption monitoring systems, automation, and laboratory measurements.

Compact Pololu 5294 current sensor based on the ACS37220 IC, designed for measuring currents up to ±200 A at a 5 V supply voltage in applications requiring galvanic isolation and an analog output. Pololu 5294

A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±10 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 132 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5440

Module with an analog current sensor. It enables the measurement of alternating and direct currents up to 50 A. Cytron BB-ACS756

The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5255

This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034

The INA3221 module, which allows simultaneous measurement of voltage and current for three power supplies via I2C with ±1% precision. With a 13-bit ADC and built-in 0.05Ω shunt resistors, it allows accurate monitoring of currents up to ±3.2A and voltages up to +26VDC. Adafruit 6062

A modern current sensor combining the Hall effect with an inductive coil, which allows for precise measurements of both the DC and AC components up to 5 MHz. Thanks to its lightning-fast response time and low path resistance, it is perfect for motor control systems, power converters and protection systems. Pololu 5232

A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±10 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5446

Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042

A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5457

A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and its low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5451